Thank You HenrikOlsson
Is there a way to fix this, or does this mean the chips are bad?
Thanks
Larryd
Type: Posts; User: Larryd; Keyword(s):
Thank You HenrikOlsson
Is there a way to fix this, or does this mean the chips are bad?
Thanks
Larryd
I started using PBP 2.6C in 2011 when Darrel Taylor was still on the forum. He helped me with a communications program
on the PIC-16F877-20/P. He thought me how to use his DT INTERRUPTS to do...
Dave, and
Mackrackit,
Thank you both Very much, This was just what I needed.
after reading http://www.picbasic.co.uk/forum/showthread.php?t=543
I now have a handle on how it all works. I...
Thank you Henrik !
Ok,
I found the file M16F81X.INC
, but do not understand what is active.
Example the include file has both ,
WDT_ON equ 3FFB0004h ; XX XXXX XXXX...
Has anyone had trouble compiling this project in PBP 2.60C
http://www.picbasic.co.uk/forum/showthread.php?t=18143
I keep grtting Error[118]. I can remove the config line,
@ __CONFIG...
In post http://www.picbasic.co.uk/forum/showthread.php?t=6013
Darrel Taylor shows an example of how to use the OWIN/OUT commands that will accept a WORD variable
that can address ANY pin on the...
Louie,
I just tested, it is 4.88 V.
Also don't know if this helps but once the 12F683 goes into the over heating mode,
I removed connections on pins 2 - 7 and it still got hotter till I...
Charlie,
when I turn the transistor around it will not work at all
Thanks
Larryd
It works now but 12F683 still gets hot, I also noticed it flashes the
power power light on the old controller after 15 seconds.
but relay is still up seems like it takes 2 cycles to release relay....
Thank you all for the Help !!
I'm new to micro controllers and have another question about the
decoupling capacitor. is this like a 0.1uf ceramic capacitor across pin
1 and 8?
Also does the...
Trying to build small power reset circuit using a PIC12f683.
When GPIO.1 goes high, I set GPIO.0 high to MPS2222
Transistor to make the circuit. Trouble is GPIO.0
dosen't go low, or if it does...
Thank You Darrel !!,
I put a 10K pullup,
Works Great now.
Thanks
Ld
PIC16F877
PBP Ver 2.6C
I can't get port A to work with LCD.
Port C and D work fine.
I'm sure I missed somthing just can't seem to find it.
Thanks
Henrik,
Thank you so much.
I have been trying to understand how to use with HSERIN, and had seen it both ways,
and wanted to understand how it works.
Thanks again.
Larryd
Question,
When using Darrel Taylor's
"DT_INTS-14.bas"
What does the Reset Flag Do?
When using with PIC 16F877
HSERIN
I have seen examples both ways, and did not understand how what it was used...
Thanks Darrel
I like having the ability to name the sensors, I will give this a try.
Thanks Again.
Ld
Thank you Darrel
Works great !
I was studying your code in this post
http://www.picbasic.co.uk/forum/showthread.php?t=6013&highlight=OWPIN%3FW
Will the code parameters be the same as...
I'm new to PBP and have been working with some DS18S20 and DS18B20 Sensors.
I'm using a PIC 16F877 here is my loop that reads the DS18S20. Is there a way
to detirmine if the sensor is a DS18B20 the...
Thank you Henrik !!
You are totally right that was the trouble.
Sorry I missed that, Slow learner I guess.
The PIC I'm Compiling for is a 16F877.
Thank you again for your help!
Larryd
I am very new to PBP, have done a good bit of research on Darrel Taylor's
DT_INTS-14 ver 1.10. I really like what I have read on this Forum about it's
abilities to do interrupts on HESRIN. I...