Hi Henrik
thank you very much on your kind support.
mike
Type: Posts; User: eltra11; Keyword(s):
Hi Henrik
thank you very much on your kind support.
mike
Hi
thank you very much on your kind support.
mike
Hi to all !
In anyone can help about writing a code for PICs
PIC 16F527
PIC 16F15244
Have PBPX 3.1.3.4 Gold and MicroCodeStudio Plus Version 5.0.0.5.
Any idea how to write code for above PICs...
Hi
Please look at the code for MPLAB.Please look if you can help about.My knowledge in MPLAB programming is very low.
Here is a CODE for multiply.Please could you make a correction that MUX_24X24...
Hi, thanks a lot !
I shall make additional efforts about this task.
Mike
Hi Ioannis
I made a trial efforts with 74HC4046 for realization of 11 time multiplying of input frequency from 1 Hz to 1 MHz.The output such have to be from 11 Hz to 11 MHz.But it is very tricky...
Hi Ioannis
thank you for your valuable comments.I shall make a test with CD4066, a mosfet 2N7000, J111, and miniature relay to try to switch C connected to PLL pins.
To switch R connected to ground...
Hi Ioannis, Hi Charlie
Thank you for your kind support.
But CD4066 have to switch the new value capacitor or R1 every 5 minutes, as the input frequency to PLL will change every 5 minutes.
Means,...
Hi Ioannis, Hi amgen
Thank you for comments.
For switching capacitor in VCO I shall try CD4066 - it has floating switch output with On resistance 5 ohm.PLL – CD74HC4046A runs on 5VDC, but I shall...
Do not understand exactly what do you mean by sentence : "The PIC could switch in 1 of 2 or 3 PLL's for workable operating ranges."
My idea is that PIC should detect the frequency frame in which PPL...
Hi Richard , Hi Henrik
You enormously help me in solving to approach to the task on the right way by conclusion that neither CCP or NCO should not lead to the solving of the problem.
As one...
Reply to mpgmike
In private correspondence with Mr. Henrik the conclusion is that solution with NCO, and PIC working on 64MHz clock would not be the solution.
Referring to your idea to measure time...
Hi
Anyone can help about the following task.
Have to multiply input frequency by 11.
The input frequency range is from 1 Hz to 1 MHz.
Output frequency has to be from 11 Hz to 11 Mhz.
Input...
Hi mpgmike
thank you very much on your suggestions and explanations.
Have a nice time
Here are what I did according to Ioannis sugestion:
In Config word:
__config _CONFIG1, _FEXTOSC_OFF & _RSTOSC_HFINT32 & _CLKOUTEN_OFF & _CSWEN_ON & _FCMEN_ON
;HFINTOSC with OSCFRQ= 32 MHz and...
Hi Ioannis
thank you very much, it works !
Anyone can help about how to realize to make 16F15355 work correctly with Internal Oscillator on 4MHz clock frequency.
How to adjust config 1 – 5 and other registers to realize that.
Here is a...
Dear Alain
thank you very much on your support
Hi Henrik
Thank you very much on concise elaboration of the all aspects of this little project.
Shall try to work it out.
By the way - may be you have knowledge where to find Melanie's document...
Hi Henrik
have just measured rise time - it is 2,5uSec (0 to 5 V positive edge) - with no distorsion on positive egde.
signal under consideration - Quadrature signal, frequency = 30 KHz.
Thank...
Hi Henrik
thank you very much on your suggestion.
Shall try the way you suggested.
Mike
8057Hi Henrik
Thank you very much on your kind reply.
First – I am new in PBP programing and PIC use.
Here is what I am trying to work out.
I shold like to measure or detect the rising edge...
I should like to use both analog comparators on the 16F628A
I would like to compare a voltage (that ranges from 3 to 0 VDC relative to ground) to the internal voltage reference set to 0.5V. If...