Search:

Hi group, The PBP manual says that the highest frequency at the HPWM's at any oscillator speed is 32767Hz. Is this correct? I'm looking for 48Khz. Also It says that if two are used they have to be...

But does it mean that the chips with three pwm's need to be the same frequency? I'll try it in the simulator then run it on the chip Thanks much for your time! Emmett

Am I at all close? I can get it to compile without it but adding a
"For HPWMFREQ2 leaves me in the dark as two FOR NEXT loops is not correct but both timers need to change frequency at the same...

Yes, they sent me one for 10 Mhz. Just takes them a little time it seems but it works fine. Emmett

Thank you Mister E. I'll check it out Emmett

How do I "port" a PBP program to ATMEL Mega48 using Bascom or similar? I need six HPWM's. Trust me, I'd LOVE to stick with PIC! I love this group and this program!!! Emmett

Does microchip have any models that can do 6 channels of hardware PWM along with three ADC channels? Thanks much once again! Emmett

Yes I do but I seem to be able to always complicate the obvious. I'll try until it makes sense like PBP is starting to. Thanks a lot for all you'all do! Emmett

Where do I find a simple explanation as to what "port" means in relation to RE0 RE1... these are port "E" right same as port RA0 RA1... are port A? and what does that have to do with pin numbers?...

Hands down, this is the best support I have ever experienced for ANY product I have ever purchased, Let alone the fact that many people who are worlds more intelligent in this field than I can ever...

I've e-mailed Mechanique several times in order to obtain a 10 Mhz bootloader file for a 16F877 at 10 Mhz but have had no reply. The 4Mhz and 20Mhz files I have, have only two characters in both...

"PORTA.0=1 ' relay is ON", Isn't PORTA.0=0 ' relay is ON?

Thank you Melanie, for this info
"For a riviting non-fiction account... I would recommend... "The Truth about Chernobyl" by Grigori Medvedev"
Got the book Via Amazon and can't get it out of my 16...

Most excellent Sir! I love when stuff works! Thank you So Much!! Emmett

Very cool, works excellent! One more proclamation of my ignorance. How do I put a space between the digits? Tried putting an actual space everywhere but it only works in the text. Thanks again for...

I'll give it a shot, Makes sense but I don't know how you do it! (know all this stuff that is) Thanks much dude! Emmett

This is the file that will run the 16x2 LCD that comes with my development board What do I need to integrate this into a program to output 4 to 6 var words two at a time. 16F877 Thanks Again all...

Ah Makes sense I love PBP and this forum! Priceless! Thanks much Melanie!

In my code there is ten or so pause's that need to be changed from time to time. How do I have the pause command look at a fixed value so that I only have to change it, instead of ten lines of code?...

Yep, it works ! Thanks much to Dwayne and Mister E without which it wouldn't have happened. The best pic forum on the net! Emmett

I believe I have it tackled Thanks so much for the invaluable input! Emmett

It'll be battery powered

Yes every 15 minutes or so no matter what the time length for the main program. I see what you mean, if the main took longer to execute then the counter wouldn't decrease in the same amount of time....

Is there any way I can talk someone into integrating the above that Dwayne contributed into this working code? I've tried several ways and only complicate the errors. Tried the COUNT command but...

Hmmm I'll try to go this route tonight makes sense but I haven't had PBP very long so I'll have to wrestle with it until it works. So there is no special "counter" that I have to set up to count...