Thanks Henrik,
The original program was for a 16F84 and I’m replacing it with the 16F87 and yes I did change that on MCS and I’m using PBP 3.1, recently upgraded. I did put comcon= 7 in the newer...
Type: Posts; User: BobK; Keyword(s):
Thanks Henrik,
The original program was for a 16F84 and I’m replacing it with the 16F87 and yes I did change that on MCS and I’m using PBP 3.1, recently upgraded. I did put comcon= 7 in the newer...
Hello,
I’m getting the same error on a 16F87 but I have 3 routines, Main, Bypass, and Alarm on a short program. I have these labels being used in if….then statements that the program is suppose to...
No I did not disable the WDT. Is that necessary?
Thank you for the fast reply, Jerson.
I have 2 inputs on port A and the Tris A is =00000011 and the outputs are on port B and the Tris B is =00000000. I have the comparators disabled with CMCON = 7....
Hello all!
It’s been a long time since I’ve posted here but I’ve still stayed in touch. I just made a project using a 16F87 and set 2
Outputs to 0 and I am getting voltage out of the pin that’s...
Hi Fidelus,
Are you planning on using this commercially? If so you might want to contact U.L. for the requirements for getting a U.L. listing which will be required by your customer's insurance...
Hi Longpole,
I hope I didn't waste your time but I had not read your previous post on your project but I just finished reading all of the replies. Boy you really have your hands full. I will...
Hi Longpole 001,
Back in 2005 I built 2 160-Input annunciator panels using 20 - 16F74 chips "talking" to a 18F452 on the master board and 20 - 16F872 chips talking to another 18F452 master. I used...
Hi all!
I have been in the alarm business for over 38 years. Most of the systems I deal with utilize an end of line resistor for supervision of the circuit and it also allows the use of open and...
Hi Queenidog,
I myself bought a V2 Development board from them and have had no problems running PBP programs on it. Are you saying that the V7 board won't allow PBP code to run on it? I even...
Hi David,
It looks like you are way in over your head with this project. I really have to ask the question I haven't seen asked yet but what are you studying in school? Has your instructor run...
Hello again,
My code section was this:
Serin2 serpin,36081,250,Main,[Wait("A"),DEC3 Apt, dec1 Event] '4/20/13 New changes
BusyOut = 1
pause 10
if Event...
Good morning all!
While updating an old program I encountered the following message:
ERROR: Macro SUB?BCL not found in macro file.
As far as I know I don't have any macros but maybe PBP...
Thanks for your replies Henrik and Charlie.
Yes the GOTO is only executed if the If Then is true. Doing it this way eliminates the End If statement for each line. At the time I tried this...
Thanks for the input Shawn. As I'm working on my new ideas I will try a series of variations that are starting to pop into my head. I will keep your comments in mind. Thanks again!
Bobk
Thanks for the reply Archangel,
In the beginning I looked at a lookup table but didn't know enough about using it so I went with the IF .. Then senario.
There are 20 slaves with 8 inputs on...
Hello group,
I currently have a master board that receives reports from 20 slave boards. When the master
receives the 3 digit number (what input) from a slave card it goes through 320 If Then...
Hello jfar22,
Did you look into the similar threads below your post? There is the information you are looking for.
I use MCS+ and MELabs USB programming and I am not familiar with ICProg but I...
Hi kduck,
How about not turning the LCD on until you actually need it? Set a pin on the PIC as an output and it turns on a transistor that can then supply the power needed by the LCD. Also...
Hi Sean,
There are quite a few samples of using PICBasicPro using SERIN, SEROUT, and writing to a LCD Display on the
MELabs website. (www.melabs.com) You will find a wealth of information to...
That's not C! It's assembly language.
BobK
Happy Holidays to all on this forum!!:love_heart:
BobK
Hi Mike,
Mind if I ask what program you are using to illustrate your drawings?
Thanks,
BobK
Hi John,
When I sent you my DS1337 schematic last year I only showed the two diodes connected to the Vcc of the 1337. I had the resistors connected to the PIC's Vcc for the very reason that you...
Hi Aberco,
I use alot of 16F87s which has the same pinout as the 16F88. I needed more code space to do more things with my product without adding parts to the board. Microchip recently came out...