"Darrel, I just wanted to say "Thanks!".
Sorry for the mistake.
(Thanks Demon)
RL
Type: Posts; User: RayL113; Keyword(s):
"Darrel, I just wanted to say "Thanks!".
Sorry for the mistake.
(Thanks Demon)
RL
David, I just wanted to say "Thanks!"
This file has fixed a problem that I have been struggling with for 3 days.
RL
Thanks Robert!
Where can I find "ALLDIGITAL.pbp"? Either download the file or get the code?
Thanks
Where can I find "ALLDIGITAL.pbp"? Either download the file or get the code?
Thanks
I didn't see ANSEL in the p18f26k80.h file.
So I tried the following using the ANCON configuration registers and it seems to work;
ADCON0 = %00000000 ;P364 A/D CONTROL REGISTER 0
ADCON1 =...
I've tried;
ANSEL = $00
ANSEL = 0
ANSEL0 = 0
and get "ERROR Line 30: Syntax error.30: Syntax error 30: Syntax error"
Any suggestions on the correct way to enter this setting in this new chip?
Thank you Henrik. When I re-posted here I thought no one had responded to the other thread. I will try your suggestion.:D
I think this would be the right place to ask this. I have a 18F26K80 that I'm trying to turn off the A/D on the A ports.
I tried the following;
ADCON0=$00 'switch the Analogue A/D pins to...
I think this thread would be the right place to ask this. I have a 18F26K80 that I'm trying to turn off the A/D on the A ports.
I tried the following;
ADCON0=$00 'switch the Analogue A/D pins...
That worked perfectly!
Thanks a bunch!
Ray
Melanie,
Can you help me with this?
I cannot get the protection to work. My devices are a 18F2680 and a 18F2620.
Here is my code;
__CONFIG _CONFIG5L, _CP_ALL & _DATA_CP_ON...
Trying to get my code to run on a PIC18LF2680. When I step thru the code I notice it skips over all of the "VAR" statements.
However, when I continue, it acts like it is performing the required...
I got it working by using 3 tables. Thanks. I never could get the word version to work. It only gave me 16 bits and I needed 24. Haven't tried the long word version yet. That's next.
Now I need to...
Thanks. I think I got that part figured out;
Display:
'Segment A = PORTB.0
'Segment B = PORTB.1
'Segment C = PORTB.2
'Segment D = PORTB.3 ...
The display is laid out like this;
RB0=A
RB1=B
RB2=C
RB3=D
RB4=E
RC0=F
RC1=G
RC2=dp
RC3=Digit-1
Got that working! Thanks for the tip,
Now on to the display. 3 digit 7 segment display, common cathode.
I want to take the port C pin states and look those up in a table.
Then Send the table...
Adding the comma worked great! Thanks
That worked great! Thanks
What about if I don't recheck with Peek and do this instead;
CHLP:
PEEK CHSEL, CHSELVAR 'Look at the 4 input pins from the channel selector
If CHSEL > CHSELVAR Then UP 'if it's larger then run...
That worked! Thanks again.
Have another little snag.
It doesn't like my Peek command syntax.
Get this error; ERROR Line 27: Bad expression.27: Syntax error
Here is line 27; PEEK CHSEL...
Thanks! I'll give that a try.
Ok, so let's say then, that I don't use the lsb as the toggle pin, and use 0 thru 3 as my 4 input bits, would the command be chsel = (PORTA) %00001111 ??
Or am I missing the point?
Thanks Steve.
But what is this doing? I mean is it assigning pins 1 thru 4 to the CHSEL label?
And "Bitwise Mask". I don't see that in the manual. What does it mean?
There's got to be an easier...
Thanks, looked right over that.