Hi Mike,
Thanks for your help, I need to use directly from PBP, I have an older version.
I'm thinking of using a single PWM PIC like PIC18F1320 to control two analogue values then use sample and...
Type: Posts; User: suded; Keyword(s):
Hi Mike,
Thanks for your help, I need to use directly from PBP, I have an older version.
I'm thinking of using a single PWM PIC like PIC18F1320 to control two analogue values then use sample and...
Hi,
I have 18F2320 has anyone used HPWM on this PIC? I have EPIC programmer is ok to program this chip?
I looks it has 16 bit PWM can I use it for 8 bit only? has anyone used both pwm's since it...
Hi Henrik,
Thanks for your help, found it.
Suded
I'm using PIC18F1320 micro.
Suded
Hi,
I'm using MAX7221 display driver, I know how to set it up.
I need to send serially a 16 bit number to the display, but I found that I need to decode the number into digits digit 1, digit 2......
Hi,
Has anyone used ARRAYREAD or ARRAYWRITE?as mentioned in ver. 2.60.
Can you please give an example?
Regards.
Suded.
Hi Darrel,
Thanks for your reply.
I checked the thread you suggested it has only I2Cwrite.
I aslo found some good software in Reynolds(Rentron) website for I2C comm. but that uses individual...
RTC is RX-8564 EPSON with built in XTAL 32.768 kHz.
Hi,
I'm using I2C command with 8564 RTC .
I2Cwrite is working ok.
I2CREAD is not giving me what I want.
ADCON1=127
sda var portb.4
scl var portb.5
dt var byte
I2Cwrite sda,scl,$A2,$0D,[80] ...
Hello Baldwics,
Find attached .pdf file on how to improve DPP resolution.
suded.
Hi,
I'm using EEPROM command with PBP,Microcode studio plus (IDE),pic18F1320
I'm not getting the right values in the EEPROM.
EEPROM 0,[0,0,0,8,0]
Only three of the above locations are...
Dear Sougota,
You are possibly trying to use the Micro (PIC XXXXX) as part of the control loop to regulate the amplitude of your sine wave.
The alternbative approach is to build the control loop...
Hi anj.
You can use any of the signals for RS 233 like Tx.
You can connect trhat to your INT 0 line as well as the normal serial connection that you are using.
The micro is normally at sleep...
Thanks Steve.
I tried it & it works.
I commented the __CONFIG line in 18F1320.INC folder in PBP directory.
Regards.
Suded.
Hi Bruce,
I tested
__CONFIG _CONFIG2H, _WDT_ON_2H & _WDTPS_512_2H
The comma error is gone (with the tab) but I have another 2 errors memory related:
Overwriting previous address...
Thanks Bruce I will try that
Hi all:
I'm trying to adjust the post scaler on 18F1220:
@__CONFIG _CONFIG2H, _WDT_ON_2H & _WDTPS_512_2H
to get more realistic sleep interval.
The assembler is giving me an error (,)the comma ...
Hello again,
Can I ask once more about Sleep command.
I'm running it OK on 16F84.
When using 18F1220 I get 1/4 of the delay value.
On the 16F84 the delay depends on processor voltage but more or...
Hi all,
Can anyone suggest why I can't get accurate time when using Sleep command with18F1220.
say:
Sleep 60
Micro goes to sleep for 1/4 of the above time.
I'm running at 20MHz .
Any...