Search Results - MEL PICBASIC Forum


Search:

Type: Posts; User: BobP; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    3,057

    Re: Can't program a 12LF1840?

    Hi All,

    SOLVED!

    I knew I was making a stupid mistake and it only took me a day to see it!

    I was powering the LF part from 5v.

    Set to 3.5v and all working.
  2. Replies
    8
    Views
    3,057

    Re: Can't program a 12LF1840?

    Hi All,

    Thanks for the replies.
    I had already selected 12LF1840 on programmer and Microcode (I had also tried 12F1840 just to be sure).

    But thanks,
    Bob
  3. Replies
    8
    Views
    3,057

    Can't program a 12LF1840?

    Hi All,

    Usually I use 12f863 in my projects but can't get them anywhere. I managed to get some 12LF1840 pics and find when I try to program them all 5 come up with the error of 'Target device does...
  4. Problems programming a 10F206 PIC using the Melabs U2 USB Programmer

    Hi All,

    Having programmed 12F, 16F and 18F parts over many years with Melabs USB programmer with no problems I am struggling trying to program a 10F206 chip.

    I get 2 error messages when trying...
  5. Re: Getting a 18F2525 to wake up from sleep with change of input

    Hi,

    Two small changes makes it work.

    Many thanks Richard I was going round in circles getting nowhere.

    Thanks
    Bob
  6. Getting a 18F2525 to wake up from sleep with change of input

    Hi All,

    Been working on this all day and I must be doing something silly!

    I want to wake up the 18F2525 from sleep by a change in port B.

    Any help appreciated as I am quickly tearing my hair...
  7. Thread: Readcode problems

    by BobP
    Replies
    2
    Views
    2,147

    Re: Readcode problems

    Hi Darrel,

    Many thanks for your reply. Once again another valuable reply, you were spot on.

    I spent hours looking for what I was doing wrong. 2 min after reading your post it now works. I just...
  8. Thread: Readcode problems

    by BobP
    Replies
    2
    Views
    2,147

    Readcode problems

    Hi,

    Have been experimenting with putting ASCII data in to code space and it didn't work as I expected. Hopefully someone will point out my stupid mistakes!!

    Using a PIC18F2525 with PicBasicPro...
  9. Thread: A Defines Request

    by BobP
    Replies
    22
    Views
    15,708

    Re: A Defines Request

    Hi Kirk,

    If you can use bulbs you will see the PWM better. Let us know how you get on?

    Bob
  10. Thread: A Defines Request

    by BobP
    Replies
    22
    Views
    15,708

    Re: A Defines Request

    Hi,

    Only had time for a quick look. But from what I can see on your diagrams in post 1. The back EMF diodes are not correctly fitted and seem to be connected differently to the prototype board....
  11. Replies
    12
    Views
    48,745

    Re: Difficulty to donwload

    please help me down load this software[/QUOTE]

    Software site is here now;

    https://sites.google.com/site/terminalbpp/

    Bob
  12. Replies
    10
    Views
    8,952

    Thanks for the replies. Unfortunately the simple...

    Thanks for the replies. Unfortunately the simple diode solution is no use! The Tx and Rx modules need a solid 5v. Any less and their range falls dramatically.

    It seems the easiest solution is to...
  13. Replies
    10
    Views
    8,952

    Generating 5v from 4 batteries

    Hello All,

    Building a small RF code transmitter and receiver units and need help finding a suitable 5v regulator. There seems to be a confusing amount of IC's to choose from. None seemingly ideal....
  14. Thread: rs232

    by BobP
    Replies
    20
    Views
    14,586

    Hi, As it runs off 3.3v here is a PDF on...

    Hi,

    As it runs off 3.3v here is a PDF on interfacing it. Hope it helps.
    http://www.crownhill.co.uk/datasheets/ZX4120%20GPS.pdf

    Bob
  15. Replies
    11
    Views
    6,395

    Hi, If you are going to use a seperate 5v...

    Hi,

    If you are going to use a seperate 5v supply say the 5v from the other PC I would strongly recommend using an optocoupler to monitor the 5v.

    Bob
  16. Replies
    11
    Views
    6,395

    Hi, I would detect the 5v from the PC's USB...

    Hi,

    I would detect the 5v from the PC's USB socket. When 5v disappears check again for about 400mS to allow for spikes then send your serial data to the other PC.

    Bob
  17. Replies
    12
    Views
    48,745

    Hi, For everyone looking for the new location...

    Hi,

    For everyone looking for the new location of Bray's terminal software, its here
    http://braypp.googlepages.com/terminal

    Took me a while to find it!

    Bob
  18. Hi, I remember the good old resistors used to...

    Hi,

    I remember the good old resistors used to change the blower speed. I am sure they gave off more heat than the heater matix did on my old Mini?

    I have been told that on this car space is...
  19. Thanks Charles, You have given me more...

    Thanks Charles,

    You have given me more information that I hoped for.

    Will be building a prototype soon. Will let you know how I got on?

    Thanks again,
    Bob
  20. Using PWM to drive 12 fan. What's the Pitfalls, if any?

    Hi All,

    Friend is building a kit car and has asked me to design a switched (3 or 4 position) speed controller for the interior heater fans (current between 6 to 10 amps total). I did suggest...
  21. Camera Flash Trigger showing assembly Interrupts within PBP

    Hello All,

    This is a program to control a camera slave flash.
    Triggered from the cameras own inbuilt flash.

    The program is very small demonstrating the use of assembly interrupts in PicBasic...
  22. Replies
    2
    Views
    3,679

    Hi, Quickest way would be to buy one of these...

    Hi,

    Quickest way would be to buy one of these Ipod/MP3 FM transmitter units. They are crystal controlled (PLL) with a choice of preset frequency. Connect pic to audio plug and get it to generate a...
  23. Thread: MSF clock module

    by BobP
    Replies
    7
    Views
    10,068

    Hi, Done this many years ago. But...

    Hi,

    Done this many years ago. But unfortunately the code was assembler and I last seen it 15 years ago?

    Few things to check. Is it MSF from Cumbria (Changed from Rugby) or DCF from Germany....
  24. Replies
    2
    Views
    2,929

    Hi, Thanks for the reply. But the part was...

    Hi,

    Thanks for the reply. But the part was definitely a transmitter. From what I remember it required no external xtal or inductors just a tuned aerial circuit. Will keep on searching.

    Bob
  25. Replies
    2
    Views
    2,929

    Low Power Transmitter in a TO39 Package

    Hello All,

    Does anyone know of a supplier (UK preferably) or manufacturer for the transmitter unit used in wireless doorbells etc. It seems to be a self contained part packaged in a TO39 (a flat...
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4