can you share your config settings?
Type: Posts; User: mehmetOzdemir; Keyword(s):
can you share your config settings?
I installed old version now everything is ok. i hope we can use last versions of mplabx with pbp3. thank you very much.
Thank you for your answers. I made a new .pbp file with no problem and compiled well but i cant see highlighters for basic commands now.
I'm using MPLABX IDE v3.40. Installed "PBP Tool Chain" and added PBP3 in options/embedded/build tools.
After all of them, i wanted to make new project. I sellected PBP3 for compiling but i...
I hadn't enough time for project, i've changed pic to 16F1824 same pin count and has EEPROM. In data sheet says HEF memory address range $0780 - $07FF. I don't know readcode/writecode works for this...
Some new pics have HEF instead of EEPROM. I realised it when i am working with 16F1503. I've changed my microcontroller which has EEPROM. Now, i'm wondering about is there anyone who used HEF with...
Hello everyone..
I read this post today. And added MOVF PORTA, W - MOVF PORTB, W. Now it's working as it should be.
RABC :
@ MOVF PORTA, W
@ MOVF PORTB, W
* There is no problem with compiling. It's okay.
* There are buttons tied PORTA.0, PORTA.1, PORTA.2 - PORTB.4 and PORTB.6. I want to get interrupt every logic change on this ports. If you look at...
The chips have arrived. I tried RAB change interrupt on a demo board. The situation is the same with isis. This is my test code below.
INCLUDE "DT_INTS-18.bas" ' Base Interrupt System...
Thanks for your reply. I tried to work it with ISIS. It may cause for it. I'm waiting for chips. I will try it again.
I'm working on a project using 18LF13K22. I need to use RAB Change Interrupt with DT Ints18. I made changes on DT_INTS-18.bas below but i couldn't succeed. Any suggestion?
#define RABC_INT ...
Thanks Alain and other friends for your replies..
The problem was solved with a small R-C snubber. Connected to A1 and A2 pins of Triac.
Hi aratti,
This is the test code that i have used always for many projects. The microcontroller is PIC16F876A. PORTB.0 is Zero Cross Detect Input. PORTB.7 is fire triac output.
INCLUDE...
I have used Opto-Triac and triac for dimming A.C halogen lamp.
I was using Pic based Zero Cross Detect dimmer Incandescent lamps with no problem.
However; when i use halogen lamps instead of incandescent lamps, The dimmer circuit isn't working properly.
So,...
I found that pdf http://ww1.microchip.com/downloads/en/DeviceDoc/ETN32_PICkit_3_Operation_at_Low_Voltage.pdf
But all these resistors are also "0" ohms in my programmer.
Hi all,
I tried to program PIC18F1320 with 3 volt(LVP).My programmer is PICKIT 3 which i bought it from Farnell.
I activated the LVP bit on config and connected the PGM pin to PICKIT 3. When i...
I used MPASM when i compiled it. Try to use MPASM or add your config settings to the top of your code.
there will be many reasons.
i think the problem is about your config settings.
compare the orginal .hex file configurations with your new .hex file.
Manuel says ;
Define >>>>> DEFINE
ok. i understood the problem . we will shift the "-" string 1 step left.
change the "ekran_0" label with below ;
ekran_0 : ; transfer the registers to diplay
mask_3 = isi dig 3
i refreshed the zip file download again.
i wrote some codes below it worked on isis.
SEGMENT_A VAR PORTB.3
SEGMENT_B VAR PORTB.7
SEGMENT_C VAR PORTB.0
SEGMENT_D VAR PORTA.3
SEGMENT_E VAR PORTA.2
...
if you are using isis for simulation , it is hard to scanning displays.
it doesnt work properly when displays are scanning.
i think this thread will help you.
http://www.picbasic.co.uk/forum/showthread.php?t=11475&highlight=Pulse+Capture+byte+building