Thanks for the input! Yea it was the VREF- set external... I was reading the bits left to right... in other words, I had my head solidly in brown town....
Type: Posts; User: thasatelliteguy; Keyword(s):
Thanks for the input! Yea it was the VREF- set external... I was reading the bits left to right... in other words, I had my head solidly in brown town....
I am not fully understanding the setup for the ADC, and therefor, I am missing something. With the following code I get my readout on the LCD, but I get 0 99.9% of the pot travel, and 255 @ POT WOT....
Ok, this is a PIC32MX440F256H.... Does this make it more complicated somehow?
That is EXACTLY what I need! I have an auto-acquire satellite dish system that is run by a PIC32, and I need it to shift itself just a few degrees left, and possibly a couple up or down, of where it...
Ok, we seem to be mixing terms tho... I was under the impression that when it comes to MC programming, that there is a distinct difference betwteen disassemble and decompile. Correct me if I am...
I understand that I will not be able to decompile, but everywhere I look, it says I should be able to disassemble. I know I'm gonna get assembly language back, but I can read assembly, I cannot read...
A thousand thank-yous my friend! It worked beautifully!
OK! I think I have my permanent solution. Since I had no problems with the first setup I did with this project where I was using physically attached buttons instead of serial commands to control the...
it started out that way. didn't work either. Also I need word-sized numbers to pass
I (think) have had a EUREKA moment! Look, my problem in a nutshell is that I cannot get serin data thru to my pic while hard interrupts are firing at 50hz. This means I can't get the data thru to...
Ive tried it hundreds of ways. It just doesn't work. Or rather, it works fine, but it will not acknowledge input from my terminal on my PC
' Name : HSERX.pbp
' Compiler : PICBASIC...
first two set the rx/tx pins. this pic has two sets. the third is interrupt edge selection... shouldnt affect usart
I have been trying for months to get a PIC16f1829 to accept input via Hserin from a PC terminal with zero success. I have discovered that PIC to PIC, it seems to work fine. So my idea is to put...
I have a PIC16F1829 running a mobile satellite dish... I have gotten hserout to work fine. Hserin, not so much. I've been trying to get it to take input from a serial terminal on my computer thru a...
OK, bummer! My debugging was buggy.... Those are only there for the moment to see where I am. My fastest encoder, according to the scope is running about 50-60 hz. So that may be the problem. I'm...
I'm unfamiliar with this black magic you speak of... tell me more...
Ok... These are quadrature encoders. Each one has two signal wires producing a dual square wave at 50% offset. Which one is first is dependent on which way the encoder is rotating. I am only using...
Last night, the azimuth on my dish was counting up 11541 to move the dish 180 deg. I changed NOTHING. I went to bed and came in this morning, and now it's only 3100. Now, in my code, I have it...
I suppose I can also scope the data coming out of the bt and into the pic, but I dont think itll yield much more than seeing the led flicker... unless you want me to somehow capture and post the raw...
Flow control.... hmmmm. Makes me think I may have somethiny else amiss... could it be terminal settings? Serin/serout works fine. I have hooked up an LED to the rx on the pic and I see it flicker on...
Are you saying these lines do not execute?
hSERIN [cereal]
if VerboseMode = 1 then HSEROUT [#cereal,13,10]
correct
OK. I got multicalc working.
I got hserout working.
hserin - notsomuch.
My menu looks fine in the terminal. (although I can't test it with interrupts firing since I can't respond and mover the...
Jury's still out on the beating... I toast them at regular intervals doing far less nefarious acts to them.... However, they are, on whole, much cheaper to replace than arduino boards.
As far as...
No I never got it working using hserin. I can't even get multicalc to run. I DID get some rather consistent gibberish through hserin, but nothing more.