Perfect!!.. Thank you Henrik :-)
Type: Posts; User: naga; Keyword(s):
Perfect!!.. Thank you Henrik :-)
Hello,
I am using http://www.dt-ints.com/DT_INTS-14/SPWM.html SPWM_INT in PB3. Getting following error. Seeking help. Thanks in advance.8316
Many Thanks,
Shall give it a try...
Hi all, Thanks again..
@Steve: could you please share your sony 12 project also..
@ Aratti: i m not good with assembly language.. Really appreciate some basic code.
Mean while i have found some...
@ Altiblade: Thank you for you code.. Still struggling.. I would really appreciate if someone can share the complete project/working code...Thanx again.
HI..desperately waiting for help..
Hello All,
Controlling timer with few buttons using darreltaylor's Elapsed Timer Routines perfectly, Would like to control wirelessly with the use of a normal TV-remote-control with the RC5...
Thanks to all, Is there any way that can porta.5 be used as output?..Thanx again.
HI ALL,
Using portb as output : working well.
Using porta.0 to 7 except porta.4 & 5 as input with pull-up resistor working well with 0v trigger, Can i use also a pull-up resistor to porta.4 &5? or...
Please paste the code,would love to see.. Regards.
@ Peterdeco1,Thank you very much .. Very nice..Working perfectly.. Thanks to all of you..
Other problem is..
When using MeLabs default (PM) Assembler compiles OK:
@ device pic12F675,...
Thanks..Shall post the complete project shortly..
Hi, The debounce was the problem..Following both codes are working after adding some delay.. I didnt use CASE.. Pls suggest if it needs to be fine tuned..Thanx..
if (ADVAL > 200) AND (ADVAL < 256)...
Thanks mackrackit, IF (ADVAL > 1) AND (ADVAL < 53) THEN ... this code is working..
Since we using ADCIN for switches, should be able to TOGGLE the ports.. I have tried with WHILE..WEND also.. no...
Hi All, tried this code, its working but is there any other reliable way....
adval var byte ' Create adval to store result
TRISA = %11111111 ' Set PORTA to all input
ADCON1 =...
Planning to connect multiple switches into single port.one ADC pin to detect voltage level when each switch for each state is pressed and each switch is associated with a voltage.connecting 8...
Thanx for the reply....
HI, Is it possible for to change EXT interrupt from portb.0 to other port(portC or D?)
Thanks In advance....
@Melanie,
Voltage Doubler working perfect for me, but i had to change R4(10k to 1k),PWM produces 3+ volts only from PIC if i use 10k as per your schematic..i dont know whats wrong with my circuit.....
Hi all,So in my post #17, which Part of a statement that is not correct..Help.
@Melanie, Should i change " HPWM 1,25,1000" TO " HPWM 1,127,1000" ? as per the PBPManual. And please let me know if any other value needs to be changed.. Actaully i'll have to finish this project...
Hi, Still not working..need help..
Thanks.
Hi all, no luck, Please gothru my code...Thanks.
Include "MODEDEFS.BAS" ' Include Shiftin/out modes
@ device PIC16F877A , xt_osc, wdt_on, pwrt_on, protect_on ,lvp_off
Define Osc 4 ...
Hi, Could you please guide me If a 4MHz oscillator and 16f877a are used. want to control with UP and Down Buttons(10 steps)
Example: (Porta.0)
PWM PORTA.0,127,10 ?
Thank you.
Thank you very Much, actually i was trying that code in proton,by mistake i pasted.will delete now.
Since you are a senior member of this forum, and you also understood what code i am searching for,...