Search:

I wish to thank all of you for your input. I know this is off topic so thanks again. Schlaray.

Has anyone been able to use the PBP compiler with the Raspberry Pi computer. I just got to a point where I can utilize the equipment I have to do something useful, and along comes the Raspberry PI...

Check : www.rentron.com It will save you a lot of time if you just want to build a Sony decoder and use it to control something.

Schlaray.

Has anyone conducted any experiments using PicBasic Pro programs to extract the image information from an AVAGO mouse chip?

It has been a very educational day Normnet. I didn't know Intel made such a board.

This will give me plenty to investigate. Thanks for the information.

Schlaray.

Thank you for the information. It looks like the Pink Module will do the job.

What I have in mind is to build an alarm system that will notify me of any abnormal condition when I am away from...

Could a PIC be configured to send an email? What I want to do is close a set of contacts and then send a predetermined message to a remote location. Both locations have internet service. I know the...

I know I can use a PIC as a dialer. What is involved to be able to close a set of contacts and send a predetermined message via Email to a remote location? Both locations have telephone lines and...

Has anyone out there had any experience with the T-962 oven. I have seen them on ebay and the shipping charge from Ca. is about $100 which seems excessive. Is there an East coast distributor where I...

The package is self contained and approved by many agencies. The programming is done in graphic mode and they provide many functions. It would eliminate the need to build a circuit board in many...

The connection is a possible substitute or alternate approach to complete a project.
Schlaray.

Has anyone out there had any experience with the IDEC SmartRelays? At first look they have a very attractive package.
Schlaray.

I thank everyone for their input. Along with ESD protection I should have included any and all other sources of distruction. Lightning strikes and an industrial type enviorment should have been...

Can anyone cite some references for ESD protection? I have a home application using a PIC and I want to insure it is not destroyed by a spark discharge after walking on a rug. I assume that all...

I am still missing something here. "Put PIC in programmer and read it?"
I am using the Melabs U2 programmer along with the Melabs Lab-X1 board to program the PIC.
"Still in the dark."

How doI get the binary code back?

I am using Microcode Studio Plus to load a Pic 16F876A with a program. Is there a procedure to read the program from the PIC after it is loaded? I neglected to save the program after loading.

After playing with the program over the weekend I discovered two registers (intcon and option_reg) were incorrectly configured. The "Clock" generating ticks was not turning off . Steping through the...

It was my error to mention dv/dt. Although I would like to measure this also, the frequency is what I am looking for.
Thank you IOANNIS for your suggestions but my thrust right now is to try and do...

The sensor connected to the A/D normally produces a constant , fixed output. The A/D output is therefore also fixed at this point in time. When a flow is present, the sensor produces a sin wave...

For sake of argument, let us say that I am using a temperature sensor. Normally the temperature (output of the A/D) is constant. When the temperature changes, I want to know the rate of change.

I am using a 10 bit A/D converter on a 16F877A. The input is from a voltage divider where one of the resistors is the sensing element. What I want to do is determine the dv/dt (frequency) across the...

Thanks for your direction. As it turns out the lab- x1 board has the all the necessary components wired right on the board. All I need is a DB9 cable. As usual, I was impatient and wanted to see the...

I have PicBasic Pro 2.47 and Microcode Studio Pro. I am using a Lab-X1 board with a 16F877A chip. The Melabs U2 programmer is between the computer and the Lab-X1 board. The compile and program...

The message here is: Why use an external RTC when I can accomplish the same function using the built in timer configured as a clock. I will study the two programs you listed and try to get on board...