I too have been experiencing this "Too many redirects" phenomenon.
Using Chrome on a Windows 10 machine.
Cheers
Barry
Type: Posts; User: Aussie Barry; Keyword(s):
I too have been experiencing this "Too many redirects" phenomenon.
Using Chrome on a Windows 10 machine.
Cheers
Barry
Ioannis, more a "select case" study programming example :D
Cheers
Barry
The drum of a clothes dryer is belt driven.
If you are looking for a slower, but fixed, rotational speed it might be easier to reduce the diameter of the pulley on the motor to achieve the desired...
Members seem keen on the "C" language path based on the number of questions and responses regarding available books for beginners.
I too am progressing down this path and note there is a distinct...
Hi Art,
Are you saying that by following the five steps outlined in your last post, a person will end up with a full version of XC8 - with all the bells and whistles?
Cheers
Barry
VK2XBP
Thanks Richard.
The PIC is being fed via a liner regulator so I am not that interested in reading Vdd.
I want to read the battery voltage feeding this 5V linear reg. The battery also feeds a 6V...
That is EXACTLY what I am trying to do!
I have looked at PIC16F1703, PIC16F1823 and the one you recommended, PIC16F18323 - all are pin compatible and have the ability to set the FVR as the reference...
the exact same wording is used in the PIC16F1829 datasheet yet that device DOES have the option to set the ADC Vref+ to the internal FVR module (ADPREF<1:0> = 11) :mad:
Some consistency would be a...
Hi Richard,
Yes, I see that now but contradictory to this diagram, the datasheet also states that the output of the FVR can be configured to supply a reference voltage to the ADC input channel:
...
Hi All,
I am working with a PIC16F1503 and would like to use the Fixed Voltage Reference (FVR) as the reference for the ADC.
I have successfully done this in the past using a PIC16F1829 but the...
Hi Richard,
I did a project a while ago which stored word values to a 24LC02 EEPROM.
The only way I could get it to work was to use the lowbyte and highbyte method that Scampy mentioned.
Can...
Thanks Henrik and Richard for responding to my post so quickly.
Henrik - your speculation and my speculation differ. Thanks for offering an opinion.
Richard - I set the T1CON register that way...
Hi All,
I am having difficulties getting a 1Hz pulse from the output of the RTCC module on a PIC18F26J50.
I have a 32.768kHz signal being fed directly to the T1CKI input from my signal generator...
Thanks Richard.
It was the xor process that I was missing.
Cheers
Barry
VK2XBP
Hi All,
I am looking to use PORTB Interrupt On Change on a PIC18F26J50 but can't get my head around how to determine which pin (PORTB.4 - 7) caused the interrupt.
I would like to set up four...
Hi Art,
Yes, the PWM output is passed through a second order low pass filter. In my case I used a Sallen-Key LPF.
Cheers
Barry
VK2XBP
Hi Michael,
The PIC12C508A doesn't have a PORTB so your WPUB statement will obviously create an error.
As mark_s has already stated, setting option register bit 6 to 0 will enable weak pull ups...
Hi All,
I am pleased to advise that I now have a very nice sine wave output from my PIC12F1822.
I dropped the FREQOUT approach and went with the lookup table method instead.
Thanks to all who...
Thanks Richard.
Your sine lu table appears non-symmetrical. Have you done this for a reason?
Cheers
Barry
VK2XBP
Thanks Henrik and Art for your responses.
Two things that should have been revealed in my original post:
1/. The trial code using PIC12F615 was only done because I had that particular chip on...
Hi All,
I am looking to generate a continuous 50Hz sine wave output using the FREQOUT command.
From the "good book", the command is FREQOUT, Pin, Onms, Frequency1, {Frequency2}
My initial idea...
Try adding a bit of capacitance from the wiper of the pot to ground - say 100nF.
This should minimise some of the variations you are experiencing.
Cheers
Barry
VK2XBP
Jaycar Electronics also sell a small selection of 8-bit pic's that you can buy over the counter for cash
Hi Henrik,
I agree with your comment however it should be noted that a lot of people can still see the LED blinking at these rates. In fact, a small percentage of the population can still see LEDs...
Hi All,
Has anyone had any experience with a 2 channel CSM slide switch?
I would like to implement a slide switch rather than an up / down button arrangement to select the PWM output for a LED...