Never mind, I first have to initialize the DS1620 ;)
Type: Posts; User: Mike2545; Keyword(s):
Never mind, I first have to initialize the DS1620 ;)
Dave, have you ever gotten a DS1620 thermal chip to work on a 18f26k22? I have tried on Ports A-C and cannot get this to communicate correctly.
Mike
Bingo!
Thanks Richard, this line
anselc = 0 '0 = Digital input buffer enableddid it!
Mike
Thanks Dave, no matter what I try on the 18F26K22 it will not jump to the interrupt. I'm ordering some different chips with 2 UARTS to give them a try.
Mike
I don't know why mine needs the path specified but it does. The DT_INTS-18 is in the PBP folder but I need to tell it INCLUDE "C:\PBP\DT_INTS-18.bas" for the file to be found.
Mike
Hello, I've been a member since 2009 and visit to search existing issues, and occasionally ask a question. I also belong to other forums that are of the electronic nature, one site uses a chat...
Dave, are you using DT_INTS for RX1/RX2 interrupts? If so, how?
Mike
Henrik, apparently Pic Basic Pro 3 does not do that you need to specify the folder.
Mike
I have had some issues with the different versions of PBP so I upgraded to Vs PBPX 3.1.0.4
This program compiles just fine but it does not enter the interrupt on RX
INCLUDE "modedefs.bas"
...
I found that you need to point the Include to the location like,
INCLUDE "C:\PBP\DT_INTS-18.bas"
Mike
OK, Pic Basic Pro 2.6L will compile the project
Version 2.60A gives these errors:
Unknown Processor(18F26k22)
Cannot open file (Include file "Pic18F26K22.inc" not found)
Processor type is...
Richard, you are right, microcode studio version is 4.0.0.0, and the PicBasic Pro version is 2.6L :p
Richard, thank you for the respose,
PBP version is 4.0.0.0
Henrick, I altered the code to include a hserin but still no luck
...
I know this is an old thread but I am trying to get the DT_INTS to work with the 18F26k22, so far no luck with either RX1 or RX2,the program will not jump to the label in the ASM macro
...
Thank you for cluing me in :D
Terribly Sorry Richard, though it might be a fuse setting :confused:
PBP ver = 2.60A
DT_INTS ver = 3.3
So far I have just a debug statement and a high/ low/ pause on PORTB.2
I added the...
Hi all, I am using PIC 18F26K22 and INCLUDE "DT_INTS-18.bas"
I get error: Symbol not previously defined (INT_ENTRY_H)
Any clues?
Thanks
Mike
mpgmike, I got the sensor to respond to my finger temp difference. Here is the code so far:
Yes, yes, I am prototyping on a Stamp :/
' {$STAMP BS2p}
' {$PBASIC 2.0}
tf VAR Byte
tc...
mpgmike,
Thanks for the response. I'll link the code for the sht11 on the parallax site and the data sheet for the sht21....
Hello all,
I have been using SHT11 and Tracy Allen's code for some time. I recently got a SHT21 and found the conversion does not work.
I found this on the Basic Stamp Forum:
Does anyone...
Not sure what the Pickit3 does, I know the MCLR pin needs to be held high (~10K resistor) to run the processor...give that a try
Check here http://melabs.com/resources/pbpmanual/ the manual gives general instructions.
Is MCLR tied high?
Well...it was swapped pins on the x-bee module header. It was my mistake for grabbing one already soldered up and not checking the pin-out.
Thanks for all the suggestions, here is the code
...
Hi Henrik,
The Pic is running at 4 MHz with internal xtal. I can receive serial with SERIN2, will try HSERIN.
The ASM interrupt will not trip and go to label Read_serial:
At work at the moment;...