Timer + rc5

Hello All,
Controlling timer with few buttons using darreltaylor's Elapsed Timer Routines perfectly, Would like to control wirelessly with the use of a normal TV-remote-control with the RC5 protocol..seeking help..Thanx.
Some thing like this:
Main:
if command = 1 then start timer
if command = 2 then stop timer
if command = 3 then toggle led
goto Main

Current Code:
define osc 4
INCLUDE "DT_INTS-14.bas"
INCLUDE "ReEnterPBP.bas"
INCLUDE "Elapsed_INT.bas" ; Elapsed Timer Routines

TRISB = %11111111
PushButton var PortB.0
DIPSwitch var PortB.1
Switch1 var PortB.2
Switch4 var PortB.3
LED var portd.3
LED1 var portd.2
Low LED
low led1

'TRISE = %00000111
' Set LCD Data port
DEFINE LCD_DREG PORTD
' Set starting Data bit (0 or 4) if 4-bit bus
DEFINE LCD_DBIT 4
' Set LCD Register Select port
DEFINE LCD_RSREG PORTD
' Set LCD Register Select bit
DEFINE LCD_RSBIT 1
' Set LCD Enable port
DEFINE LCD_EREG PORTD
' Set LCD Enable bit
DEFINE LCD_EBIT 0
' Set LCD bus size (4 or 8 bits)
DEFINE LCD_BITS 4
' Set number of lines on LCD
DEFINE LCD_LINES 2
' Set command delay time in us
DEFINE LCD_COMMANDUS 2000
' Set data delay time in us
DEFINE LCD_DATAUS 50

LCDOUT $FE, 1, "Hello" ' Clear display and show “Hello”

ASM
INT_LIST macro ; IntSource, Label, Type, ResetFlag?
INT_Handler TMR1_INT, _ClockCount, PBP, yes
endm
INT_CREATE ; Creates the interrupt processor
ENDASM

@ INT_ENABLE TMR1_INT ; Enable Timer 1 Interrupts

GOSUB ResetTime ' Reset Time to 0d-00:00:00.00
GOSUB StartTimer ' Start the Elapsed Timer

Main:
If PushButton=0 then GOSUB ResetTime ' Check for Button Press
While PushButton=0 : Wend
If Switch1 =0 then GOSUB StartTimer ' Check for Button Press
While Switch1 =0 : Wend
If DIPSwitch=0 then GOSUB StopTimer ' Check for Options
While DIPSwitch=0 : Wend
If Switch4 =0 then GOSUB tog ' Check for Button Press
IF SecondsChanged = 1 THEN
SecondsChanged = 0
LCDOUT $FE,2, DEC Days,"d-",DEC2 Hours,":",DEC2 Minutes,":",DEC2 Seconds

If Seconds > 0 And Seconds = 5 Then High LED1
If Seconds > 5 And Seconds = 10 Then Low LED1 : Seconds = 0
ENDIF
GOTO Main

tog:
Toggle LED ' Toggle LED at each Button Press
pause 250
return

HI..desperately waiting for help..

Hi Naga,

I did some RC5 controlled projects last year.
I did some searching but i could only find some of my test code.
You should read the info found on http://www.sbprojects.com/knowledge/ir/rc5.htm this will give you an idea of how it works and a schematic ...

Best regards, UB

Code:

---

'==== Set fuses =========================
@ device pic10F202,wdt_off,mclr_off,protect_off

'==== Set XTAL =========================
DEFINE OSC 4                                    ' int XTAL @ 4 Mhz

'==== Set variables ======================
Y      VAR word                                      ' To Hold the 12-bit RC5 code
TMP    var BYTE

'==== Set IO ===========================   
IR_PIN  VAR GPIO.3                              ' GPIO.0 input pin reading IR data
SDA    var GPIO.0
SCL    var GPIO.1
'errled  var GPIO.2

OPTION_REG.7 = 0                                ' Internal pull-ups = on
TRISIO = %00001000                              ' Set TRIS register input's & output's
OPTION_REG.5 = 0                                ' Set Timer inc. on internal inst.
GPIO  = %00000000                              ' Set all digital low

'==== Signal information ==================
'Given the information found on http://www.sbprojects.com/knowledge/ir/rc5.htm
'
'bit      1    2    3    4    5    6    7    8    9  10  11  12  13  14
'      |    |    |    |    |    |    |    |    |    |    |    |    |    |    |
'uSec  1778 1778 1778 1778 1778 1778 1778 1778 1778 1778 1778 1778 1778 1778

'==== Main program ====================== 
MAIN:
IF IR_PIN = 1 THEN GOTO MAIN                    ' Wait for the first bit to arive
y.13 = IR_PIN                                          ' Incoming signal
pauseus 889                                          ' In order to see this 0 we are in the second
                                                      ' period of the first 1.778 msec, so we will
                                                ' wait another 889 usec to enter the 2nd period.

pauseus 1600                                    ' Almost at the end of the second period, look for
y.12 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.11 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.10 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.9 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.8 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.7 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.6 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.5 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.4 = IR_pin                                    ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.3 = IR_pin                                  ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.2 = IR_pin                                  ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.1 = IR_pin                                  ' a high or low signal
pauseus 178                                    ' Time to the end of this period

pauseus 1600                                    ' Almost at the end of this period, look for
y.0 = IR_pin                                  ' a high or low signal
pauseus 178                                    ' Time to the end of this period

y = ~y                                          ' Invert y word

if Y.lowbyte = 255 then goto ERROR      ' If all lowbytes are 0xFF then noise is received

TMP.1 = Y.13
TMP.0 = Y.12
if not tmp = 3 then goto error

TMP.4 = Y.10
TMP.3 = Y.9
TMP.2 = Y.8
TMP.1 = Y.7
TMP.0 = Y.6
if not tmp = 0 then goto error

TMP.2 = Y.5
TMP.1 = Y.4
TMP.0 = Y.3
if tmp > 0 then goto error

TMP.2 = Y.2
TMP.1 = Y.1
TMP.0 = Y.0

' TMP now holds the decoded RC5 signal

'==== End of main loop reset and go from top ====
ERROR:                                       
Y=0
tmp=0                                      ' Clear key codes
PAUSE 250                                  ' debounce
GOTO MAIN                                  ' Return to main loop

END

---

@ Altiblade: Thank you for you code.. Still struggling.. I would really appreciate if someone can share the complete project/working code...Thanx again.

I can't help you with working RC5 code, but here's a Microchip application note that gives some info about using a 10F206 to build a small IR remote transmitter. It talks a little about RC5 and Sony 12 formats.

http://ww1.microchip.com/downloads/e...tes/01064A.pdf

I've got some working test code that receives Sony12 and displays the button pressed on an LCD display, but that probably won't be much help to you.
I haven't learned RC5 yet....



steve

Naga, there is a code example (in assembly) @ the following link: http://www.freescale.com/files/micro...ote/AN3402.pdf

May be you can use it.

Al.

Hi all, Thanks again..
@Steve: could you please share your sony 12 project also..
@ Aratti: i m not good with assembly language.. Really appreciate some basic code.
Mean while i have found some code,it worked out as what i expected but its for proton IDE...and also i tried to convert in PBP..no success.
Site: http://www.picbasic.nl/indexes_uk.htm
Projects / 10outputs and univarsal rc5 etc..

Here's my bit of test code that displays on an LCD which button is pressed on my remote. This is for the Sony 12 bit format.

Much of the code was simply stolen from this page "Controlling the world from your armchair":
http://www.picbasic.co.uk/support/Article.pdf

--------------------------------

Code:

---

'Test program for 16F727 with IR sensor (PNA4612M)

'****************************************************************

Include "MODEDEFS.BAS"  ' Include Shiftin/out modes
DEFINE LCD_DREG PORTD    ' Set LCD Data port
DEFINE LCD_DBIT 4        ' Set starting Data bit (0 or 4) if 4-bit bus
DEFINE LCD_RSREG PORTC  ' Set LCD Register Select port
DEFINE LCD_RSBIT 5      ' Set LCD Register Select bit
DEFINE LCD_EREG PORTC    ' Set LCD Enable port                                                 
DEFINE LCD_EBIT 6        ' Set LCD Enable bit
DEFINE LCD_BITS 4        ' Set LCD bus size (4 or 8 bits)
'DEFINE ADC_BITS 8        ' Set number of bits in ADC result
'DEFINE ADC_CLOCK 3      ' Set clock source for ADC (rc = 3)
'DEFINE ADC_SAMPLEUS 100  ' Set ADC sampling time in microseconds
DEFINE OSC 8            ' 8 MHz Osc.
define I2C_SCLOUT 1      ' Set I2C Clock to drive high instead of needing pullup


'?????????????????????????????????????????????????????????????????

@  __config _CONFIG1, _DEBUG_OFF & _PLL_EN & _BORV_2_5 & _BOR_ON & _CP_OFF & _MCLRE_OFF & _PWRT_EN & _WDT_ON & _INTOSCIO
@  __config _CONFIG2, _VCAP_RA6

OSCCON = %00100000            'Set Osc to 8MHz.
OPTION_REG = %10101111
CPSCON0.0 = 1

TRISA= %00000000    'Set 'em all to outputs
TRISB= %11111111        'Set portB to inputs
TRISC= %00000000    'Set portC all outputs
   
ANSELA= %00000000        ' Set all pins to digital...
ANSELB= %00000000  ' Set all pins to digital
ADCON0 = %00100001
'??????????????????????????????????????????????????????????????????????

' Alias pins - LCD
backlight var  PORTC.2  'LCD backlight
RW      var    PORTC.7  'LCD R/W

'Alias pins - I.R. Input
IRinput  var    PORTB.0

'Allocate IR Sensor variables
Bitcnt      var    byte    'Loop counter
Header      var    Word    'Hold the length value of the first PULSIN to check for header.
P_Val      var    word    'Hold the length value of each consecutive bit in it's turn.
Packet      var    word    'Stores the raw code built up from 12 cycles of counting P_Val
IR_Dev      var    byte    'Stores the code # for the DEVICE being addressed (decoded from Packet)
IR_But      var    Byte    'Stores the code # for the BUTTON pressed. (decoded from Packet)
clear

pause 200  'Give the LCD a chance to wake up
Lcdout $fe,1 'reset LCD
HPWM 1,127,200  'Set the backlight brightness
LCDOUT $fe,2, "    test"  'print "test" and pause for a second.
pause 1000
LCDOUT $fe,1            'clear the display


' Receive a signal from a Sony remote control,
' and return with the 7-bit BUTTON code in the variable
' IR_BUT and the 5-bit DEVICE code in the variable IR_DEV.
' If no header then IR_DEV, IR_BUT will hold 255

' MAIN PROGRAM LOOP
Again:     
    Gosub IRIN ' Receive an IR signal
    If IR_Dev=255 then goto Again ' Check for valid header
    If IR_Dev=0 then goto Again ' If not a valid device code then look again
    If IR_But=0 then LCDOUT $fe,2,  "0, Channel 1      "
    If IR_But=1 then LCDOUT $fe,2,  "1, Channel 2      "
    If IR_But=2 then LCDOUT $fe,2,  "2, Channel 3      "
    If IR_But=3 then LCDOUT $fe,2,  "3, Channel 4      "
    If IR_But=4 then LCDOUT $fe,2,  "4, Channel 5      "
    If IR_But=5 then LCDOUT $fe,2,  "5, Channel 6      "
    If IR_But=6 then LCDOUT $fe,2,  "6, Channel 7      "
    If IR_But=7 then LCDOUT $fe,2,  "7, Channel 8      "
    If IR_But=8 then LCDOUT $fe,2,  "8, Channel 9      "
    If IR_But=9 then LCDOUT $fe,2,  "9, Channel 0      "
    If IR_But=11 then LCDOUT $fe,2, "11 Enter          "
    If IR_But=14 then LCDOUT $fe,2, "14 Guide          "       
    If IR_But=16 then LCDOUT $fe,2, "16 Channel Up    "
    If IR_But=17 then LCDOUT $fe,2, "17 Channel Down  "
    If IR_But=18 then LCDOUT $fe,2, "18 Volume  Up    "
    If IR_But=19 then LCDOUT $fe,2, "19 Volume Down    "
    If IR_But=20 then LCDOUT $fe,2, "20 Mute          "
    If IR_But=21 then LCDOUT $fe,2, "21 Power          "
    If IR_But=37 then LCDOUT $fe,2, "37 TV/VCR input  "
    If IR_But=42 then LCDOUT $fe,2, "42 Record        "
    If IR_But=51 then LCDOUT $fe,2, "51 Right          "   
    If IR_But=52 then LCDOUT $fe,2, "52 Left          "
    If IR_But=54 then LCDOUT $fe,2, "54 Sleep          "
    If IR_But=58 then LCDOUT $fe,2, "58 Info          "
    If IR_But=59 then LCDOUT $fe,2, "59 Repeat        "
    If IR_But=64 then LCDOUT $fe,2, "64 Play          "
    If IR_But=65 then LCDOUT $fe,2, "65 Pause          "
    If IR_But=67 then LCDOUT $fe,2, "67 Scan +        "
    If IR_But=68 then LCDOUT $fe,2, "68 Scan -        "
    If IR_But=77 then LCDOUT $fe,2, "77 Stop          "
    If IR_But=91 then LCDOUT $fe,2, "91 PIP Toggle    "
    If IR_But=95 then LCDOUT $fe,2, "95 PIP Swap      "
    If IR_But=96 then LCDOUT $fe,2, "96 Menu, Quit    "
    If IR_But=101 then LCDOUT $fe,2,"101 Select        "   
    If IR_But=116 then LCDOUT $fe,2,"116 Channel Up    "
    If IR_But=117 then LCDOUT $fe,2,"117 Channel Down  "
    Goto Again ' Repeat until nauseated...

IRIN:   
    IR_Dev=255:IR_But=255 ' Preset the Return variables
    Pulsin IRinput,0,Header ' Measure the header length.
    If Header < 450 then Return' If the result is less than 450 toss it out
    If Header > 520 then Return' If the result is greater than 520 toss it out 
' Receive the 12 data bits and convert them into a packet
    For Bitcnt=0 to 11 ' Create a loop of 12
    Pulsin IRinput,0,P_Val ' Receive the IR pulses
    If P_Val >= 190 then ' If >= 190 then we've received a 1
        Packet.0[Bitcnt]=1 ' So set the appropriate bit
        Else
        Packet.0[Bitcnt]=0 '...or clear the appropriate bit
    Endif
    Next
   
    IR_But=Packet & %01111111 'Extract the 7 BUTTON bits
    IR_Dev=(Packet >>7) & %00011111 'Right shift and extract the 5 DEVICE bits   
    lcdout $fe,1, dec IR_But, "    ", $fe,$c0, dec IR_Dev, "  ", dec header   
return
   
  end

---

----

steve

Many Thanks,
Shall give it a try...