12F683 _CONFIG problem

Started what I thought would be a quick turnaround to build a board to capture pulses from a rain gage and send to a master board. PicProto8 board and a 12F683 should do nicely. Why do things always have to get complicated? I want to use DT's to catch the pulses so I am assembling with MPASM.
PROBLEM wiith compiler error _CONFIG. Nothing I have done will clear the error. Things are compileng fine on other devices.

Error[122]c:\phpprog\wkfolder\12F683-1.asm 97:illegal opcode (_HS_OSC)
Error[122]c:\phpprog\wkfolder\12F683-1.asm 97:illegal opcode (_CPD_OFF)

DT's are commented out until first compile of simple code.

Items check of for this type of problem.
1. Does drop down minue display correct PIC? check!
2. Does Assembler point to C:\Program Files\Microchip\MPASM Suite? check!
3. Are config setting the same as in the MPASM INC file? check!

I also tried commiting out PBP\12F683.INC config line as was Darrels advise on a simular issue years ago, no help.
What have I missed?

Wayne

Code:

---

asm
_CONFIG _HS_OSC & _MCLRE_OFF & _WDT_OFF & _PWRTE_OFF 
_CONFIG _CPD_OFF & _BOD_ON & _IESO_OFF & _FCMEN_OFF
endasm
;=================   
;include "DT_INTS-14"
;include "ReEnterPBP"
;Include "MODEDEFS.BAS"  ; Include for Shiftin/out modes
;=================
;    wsave  Var byte $20 SYSTEM
;    wsave1 var byte $A0 SYSTEM
    define OSC 20
    OPTION_REG = %01000000    ;Option register p.14DS  bit6-rising edge
    OSCCON =%00000000        ;External Res p.22DS
    ANSEL  = 0                ;All pins set to digital I/O    p.35datasheet
    CMCON0 = 7                ;comparators off
    VRCON  = 0
    ADCON0 = 0
    GPIO=  %00000000       
    TRISIO= %00001100        ;sets GPIO.2 AND GPIO.3 as input others outputs   
    IOC=    %00001100          ;interrupt on change on GPIO2 and GPIO3
    WDTCON= %01001            ;WDT control
    INTCON= %10001000        ;Interrupt control - GPIO Change Interrupt Enable p.15DS
;=================     
;Variables
    Avar    VAR BYTE  ;general variable
    Bvar    VAR BYTE  ;general variable
    Cvar    var byte  ;general variable
;GPIO actioins   
    LED          var GPIO.0 ;general I/O - output
  TX            var GPIO.1 ;Send all data to master unit - Output
  Raincount    var GPIO.2 ;counts rain in 1/10 inch per pulse -input
  Sendnow    var GPIO.3 ;input post to send data out after - input
; Gpio4&5 on resonator
;=================
;ASM
;INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
;        INT_Handler    INT_INT,  _MyISR,  PBP,  yes
;    endm                         
;    INT_CREATE    ; Creates the interrupt processor
;ENDASM   
;@ INT_ENABLE  INT_INT 
;================= 
Start:
    HIGH    LED
    pause  100
    low    LED
    pause  100
    goto start
    end

---

Try indenting the _CONFIG... lines between ASM and ENDASM.

/Henrik.

also is it

_CONFIG or __CONFIG.


also

trying to place config on two lines that way will lead to overwrite error/warning

at least in pbp3 not sure about dinosaur versions

thanks for responding. So I tried all above suggestions with no luck.

IF (CODE ON ONE LINE)

Code:

---

asm
_CONFIG _HS_OSC & _MCLRE_OFF & _WDT_OFF & _PWRTE_OFF & _CPD_OFF & _BOD_ON & _IESO_OFF & _FCMEN_OFF   
endasm

---

THEN iLLEGAL OPCODE (_HS_OSC) Character after Config illegal

IF

Code:

---

asm
_CONFIG, _HS_OSC & _MCLRE_OFF & _WDT_OFF & _PWRTE_OFF & _CPD_OFF & _BOD_ON & _IESO_OFF & _FCMEN_OFF   
endasm

---

THEN ILLEGAL CHARACTER (,) Character after Config illegal, with or without space after (,)

IF

Code:

---

@_CONFIG, _HS_OSC & _MCLRE_OFF & _WDT_OFF & _PWRTE_OFF & _CPD_OFF & _BOD_ON & _IESO_OFF & _FCMEN_OFF

---

THEN ILLEGAL CHARACTER (,)

IF space after @ then Illegal opcode (_CONFIG)

If i turn off MPASM assembler it WILL assemble OK. looks like interrupts will have to be in ASM is I can't get this worked out. Oh well, I need the practice.

Why are you putting the pic config stuff in the assembler code sections?

Here is one of my 12F683 configs..

It should be right at the start of the program.

Code:

---

#config
 __config _FCMEN_ON & _IESO_ON & _BOD_OFF & _CPD_OFF & _CP_OFF & _MCLRE_OFF & _PWRTE_OFF & _WDT_OFF & _INTOSCIO
#ENDCONFIG 

DEFINE OSC 8                        'Set PicBasic Pro processor speed to 8 Mhz (Must match oscillator value)

INTCON = %10001000                'Internal oscillator 
OSCCON = %01110101                'Sets internal osc to 8 Mhz (Default) and stable
CMCON0 = %00000111                'Comparators off
TRISIO = %00101011                'Set Pins GPIO.0, GPIO.1 GPIO.3 & GPIO.5 as inputs
ANSEL  = %00000000                'No Analog Inputs
OPTION_REG = %01111111        'Global Enable Weak Pull Ups
WPU    = %00000011                'Weak Pull Ups Enabled on GPIO.0 & 1

---

I had to once, find the '683' INC or MAC file referred to by the assembler, look at the way the configs are expected in those files. I had to change my code to match the referenced/expected format/characters

I've never seen it done like that before and I also use DT stuff and 16f83...

Plus to the above, you still had one underscore instead of the correct two.

Ioannis

I have used the following header for the 12F683 many times and never encountered any compiling problems. Try it.

CMCON0 = 7 'comparators off
ANSEL = 0 'all inputs digital, the adcin command automatically converts it to analog
DEFINE OSCCON_1K 1 ' Set OSCCAL for 1K device to accurize osc
OSCCON = %01110111 'Set osc to 8MHZ 12F683. Normally I leave this line out to default to 4MHZ
@ DEVICE MCLR_ON, INTRC_OSC_NOCLKOUT, WDT_ON, BOD_OFF, PWRT_ON, PROTECT_ON

START:

I think you refer to an ancient version of PBP.

Now we do not use this @ DEVICE MCLR_ON.....

Current versions use this syntax:

Code:

---

#config
 __config _INTRC_OSC_NOCLKOUT & _WDT_ON & _BOD_OFF & _MCLRE_ON & _CP_OFF
#endconfig

---

Ioannis

Yes it is old. I think it's version 2.65 or something.