Error Compiling with PbP 3

Hello Guys !

Finally, I got my PbP 3 License last week.

I have just installed it in my notebook and tryed to compile an old source code designed for 16F877A.

My source code is using the Darrell's interrupts, lcdbar and some other resources.

As I define a new @ __CONFIG on my source code, I commented a line on the .INC file on my old 2.46 version to avoid the error : overwriting previous address contents (2007)

Now, I´m trying to compile the same source code on my PbP 3 and MPASMX.

The error showed up again, of course, because I did not edit the new inc file.

Following the advice Henrik Olsson gave on the post bellow :


http://support.melabs.com/archive/in...p/t-1065.html?

My original code :

Code:

---

@ ERRORLEVEL -306  ; Retira o erro de crossing page boundary
@ __CONFIG  _CP_OFF  & _DEBUG_OFF & _CP_OFF & _CPD_OFF & _LVP_OFF & _BODEN_OFF & _PWRTE_ON & _WDT_OFF & _XT_OSC   


Include "LCDbar_INC.bas"
Include "DT_INTS-14.bas"    ' Base Interrupt System
Include "ReEnterPBP.bas"    ' Include if using PBP interrupts

define OSC 4

---

When I compile, I get the overwriting previous address contents (2007) error, because we have two __CONFIG on ASM.

So, I put the #CONFIG / ENDCONFIG in the code , like this :

Code:

---


#CONFIG
@ ERRORLEVEL -306  ; Retira o erro de crossing page boundary
@ __CONFIG  _CP_OFF  & _DEBUG_OFF & _CP_OFF & _CPD_OFF & _LVP_OFF & _BODEN_OFF & _PWRTE_ON & _WDT_OFF & _XT_OSC   
#ENDCONFIG

Include "LCDbar_INC.bas"
Include "DT_INTS-14.bas"    ' Base Interrupt System
Include "ReEnterPBP.bas"    ' Include if using PBP interrupts

define OSC 4 l

---

Now, when I compile, I get the errors :

[ASM ERRORS] COMPB.ASM (29) : Illegal label (@)
[ASM ERRORS] COMPB.ASM (30) : Illegal label (@)

I would not like to edit the INC files anymore.

So, could someone, please, help me ?

Is there a specific place where I have to put the #CONFIG... block on the code ?

Thank you very much

Sérgio

Try this link about meConfig.

You didn't follow my advice from the other thread....
When you use the #CONFIG/#ENDCONFIG block you can't also have the @ in there and you can only set the CONFIG bits with it, you can't include the error lever stuff within the block. So, the original

Code:

---

@ ERRORLEVEL -306  ; Retira o erro de crossing page boundary
@ __CONFIG  _CP_OFF  & _DEBUG_OFF & _CP_OFF & _CPD_OFF & _LVP_OFF & _BODEN_OFF & _PWRTE_ON & _WDT_OFF & _XT_OSC

---

Becomes

Code:

---


@ ERRORLEVEL -306  ; Retira o erro de crossing page boundary
#CONFIG
  __CONFIG  _CP_OFF  & _DEBUG_OFF & _CP_OFF & _CPD_OFF & _LVP_OFF & _BODEN_OFF & _PWRTE_ON & _WDT_OFF & _XT_OSC
#ENDCONFIG

---

/Henrik.

Thank you Henrik and TabSoft !

I will test it today !

My best regards.

Sérgio Pinheiro

Hy Guys !

thank you for the tips. It worked !

My best regards.

Sérgio

Hi !
For me the solution don't work ? Any others sugestions ? Thanks !
Attachment 8414

It doesn't work for you because you have not applied the solution. Read the thread again.

/Henrik.

Thanks for fast reply !
But ... I don't understand what I do wrong :( ...
I wrote :

Quote:

---

@ ERRORLEVEL -306
#CONFIG
__CONFIG _XT_OSC & _WDT_OFF & _PWRTE_ON & _MCLRE_ON & _BODEN_ON & _LVP_OFF & _CP_ON
#ENDCONFIG

---

Exactly like in post #3.
Attachment 8415

But that's not the same code - or error - as in your previous post now, is it?
Now you've fixed the "Overwrting previous address" error and you're facing a completely different issue.

First try commenting out the Include statement to see if the problem is within that piece of code.
Then please post the code, within code tags, so we don't have to retype it and make our own errors.

/Henrik.

No change !
Attachment 8416

Code:

---

@ ERRORLEVEL -306
#CONFIG
 __CONFIG _XT_OSC & _WDT_OFF & _PWRTE_ON & _MCLRE_ON & _BODEN_ON & _LVP_OFF & _CP_ON                 
#ENDCONFIG

;INCLUDE "D:\PBP\ALLDIGITAL.PBP"
DEFINE OSC 4            ' 4MHz
CMCON = 7                ' Disable on-chip comparator, PORTA in digital mode 

TRISA = %00011100                 
PORTA = %00011100
TRISB = %00000000
PORTB = %00000000

oldState VAR BYTE
newState VAR BYTE
status_1 VAR BYTE
status_2 VAR BYTE
status_3 VAR BYTE
DIR      VAR Byte
j        var byte
BitCount VAR BYTE                  ' Index variable for above array
i        VAR BYTE                  ' General purpose

dir = 2
Main:
    PortA.1 = 0
    newState = PortA & %00011100        ; this is for my hw : 11100 = 28
    PortA.1 = 1

---

You seem to have the 628 selected in one of the screenshots, and the 628A in the other.
Which device is teh code INTENDED for and which device do you have selected in the dropdown list?

/H.

Sorry, is 16F628A !
Attachment 8417

Well, then there must be some hidden character in there because if I copy/paste the code from post #10 above and compile it for a 16F628A it works just fine.

Or you have version 2.6 or older...

Surely THAT can't be it when the thread title is Error Compiling with PbP 3 located in the forum section called PBP3....or can it... :-)

Don't know how...but solved. Thanks !
Attachment 8418