DT's Instant Interrupts trouble

Hi,
I'm very new to the interrupts but I came across Darrel Taylor's instant interrupts and wanted to give it a try. So I tried his program to toggle the led with no problems (thanks Darrel). A pushbutton connected to RB0 (INTE) interrupts main loop and a LED toggles.

Code:

---

CMCON = 7                    ' PortA = digital I/O
LED1  VAR  PORTA.1

INCLUDE "DT_INTS-14.bas"    ; Base Interrupt System
INCLUDE "ReEnterPBP.bas"    ; Include if using PBP interrupts

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
    INT_Handler    INT_INT,  _ToggleLED1,  PBP,  yes
    endm
    INT_CREATE              ; Creates the interrupt processor
ENDASM

@  INT_ENABLE  INT_INT    ; enable external (INT) interrupts

Main:
@ sleep
GOTO Main

'---[INT - interrupt handler]---------------------------------------------------
ToggleLED1:
  TOGGLE LED1
@ INT_RETURN

---

So now I'm feeling adventurous and wanted to try the interrupts on PortB (RBC_INT). Replaced INT_INT with RBC_INT and moved the switch to B1 but my LED won't toggle anymore when I push the switch (no interrupts)

Code:

---

CMCON = 7                    ' PortA = digital I/O
LED1  VAR  PORTA.1

INCLUDE "DT_INTS-14.bas"    ; Base Interrupt System
INCLUDE "ReEnterPBP.bas"    ; Include if using PBP interrupts

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
    INT_Handler    RBC_INT,  _ToggleLED1,  PBP,  yes
    endm
    INT_CREATE              ; Creates the interrupt processor
ENDASM

@  INT_ENABLE  RBC_INT    ; enable external (INT) interrupts

Main:
@ sleep
GOTO Main

'---[INT - interrupt handler]---------------------------------------------------
ToggleLED1:
  TOGGLE LED1
@ INT_RETURN

---

Am I supposed to do something else for RBC_INT?

Thanks,
Tom

What chip are you using? Many have only on the 4 upper bits of portb the Interrupt on change feature.

Also check if the option register is set properly or any other register according to the PIC you are using.

Ioannis

16F628A. I moved the switch to RB.5, now my led dims but doesn't turn off when push button is pressed.

Put an osciloscope on the LED port and you will see why.

You keep on toggling the port while pressing the button and that's why you see the LED dimming.

Other than that your program is OK!

Ioannis

It did toggle with my previous setup with switch on B.0 using INT_INT so it should toggle now on B.5 using RBC_INT as well.

When I press the switch I get 2.2V on the led

I think the problem is due to some noise on the lines as my led fill go on/off when I touch the wires. Never had it on B.0, the toggling was smoth with no noise and no dimming.

Works now.
I changed the RC values of my switch debouncing and changed the interrupt rutine from:

Code:

---

toggle led1

---

to

Code:

---

low LED1
pause 50
high led1
pause 50

---

Now it works providing I don't hold the switch for too long or it triggers another interrupt.

Code:

---

CMCON = 7                    ' PortA = digital I/O

INCLUDE "DT_INTS-14.bas"    ; Base Interrupt System
INCLUDE "ReEnterPBP.bas"    ; Include if using PBP interrupts

LED1  VAR  PORTA.1

ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
    INT_Handler    RBC_INT,  _ToggleLED1,  PBP,  yes
    endm
    INT_CREATE              ; Creates the interrupt processor
ENDASM

@  INT_ENABLE  RBC_INT    ; enable external (INT) interrupts

Main:
  @ sleep
GOTO Main

'---[INT - interrupt handler]---------------------------------------------------
ToggleLED1:
  low LED1
  pause 50
  high led1
  pause 50
@ INT_RETURN

---

For interrupt-on-change you need to read the port to allow the interrupt flag bit to be
cleared. This takes a snap-shot of the port logic, and triggers the interrupt-on-change
again once the value on the port changes after the last read.

To prevent it from interrupting if you hold a button down too long, then release it, just
use a while/wend to wait for the button to be released. I.E. wait until the switch is
released before exiting your interrupt handler. Then only the change when your switch is
pressed should generate the interrupt.

Thanks Bruce that did it!
By the way, your website is very informative.