Time limit while waiting for input ?
I'm using a 16F628A to control a DC motor, also using hall effect sensors as limit switches. All working fine however I'm concerned that if one of the hall sensors should fail the motor will keep running, NOT GOOD !
The code waits for a low from the hall sensor, is it possible to have a time limit on how long to wait for that low input and if it doesn't happen, the timer will effectively provide the low and the program can continue just as if the sensor worked ?
For example, the sensor should go low at about 16 seconds, At 18 seconds the timer could provide the low if the sensor didn't. (?)
Thanks for advice !
Re: Time limit while waiting for input ?
Quote:
is it possible to have a time limit on how long to wait for that low input and if it doesn't happen, the timer will effectively provide the low and the program can continue just as if the sensor worked ?
the code I posted in this link
http://www.picbasic.co.uk/forum/show...ht=#post136604
effectively does this. that's what "run_count" is all about
when the motor is moving the limit switches are checked every so many mS and the run count decremented
if a limit is reached or the run count reaches 0 then movement is terminated.
a run count of 2000 @ 50mS = 100 seconds till timeout
or
a run count of 185 @ 100mS = 18.5 seconds till timeout , simply adjust to suit
Re: Time limit while waiting for input ?
Hi Richard,
I've been studying your code, (again) I haven't tried to compile the items added in red below as I'm on a different PC right now. I just posted a small part of it for learning.
Can you tell me if I'm on the right track with how I've added it ?
So after 100 seconds, if the limit hasn't sent a low, limup pin will still go low ?
Thanks !
Code:
maxrun con 2000 ; 2000 = 100 sec
RUN_COUNT VAR word
moveup:
high blue
pause 500
low blue
while limup = 1
high up
wend
IF RUN_COUNT THEN ;should the motion continue ?
RUN_COUNT = RUN_COUNT -1
ENDIF
if limup = 0 then
low up
goto run
else
goto moveup
endif
Re: Time limit while waiting for input ?
hi sam
I will make some assumptions here
blue is a led that should flash when moving
up enables movement
limup stops movement when low
this is the movement loop / the only way it stops is if limup = 0
Quote:
while limup = 1
high up
wend
its not what you want
try some thing like this
Code:
moveup:
high blue ; led on
high up ; motor on
RUN_COUNT=200 ; set time limit 200*500mS ie 100 sec
while (limup = 1 ) && ( RUN_COUNT>0) ; do this till time runs out or limit sw trippe
pause 500
toggle blue ; flash led
RUN_COUNT = RUN_COUNT -1
wend ; all done
low blue
low up
Re: Time limit while waiting for input ?
Richard, you're awesome ! thanks very much !
This morning is the first chance I've had to try it without constant interruption. I must have done something a little different because it wouldn't work until I added...
Quote:
moveup:
high blue ; led on
high up ; motor on
RUN_COUNT=200 ; set time limit 200*500mS ie 100 sec
while (limup = 1 ) && ( RUN_COUNT>0) ; do this till time runs out or limit sw trippe
pause 500
toggle blue ; flash led
RUN_COUNT = RUN_COUNT -1
wend ; all done
IF limup = 0 OR RUN_COUNT =>0 THEN
low blue
low up
ENDIF
Not sure why it doesn't work right without the ">0" but in any case, it's working great. Thanks again !!
Re: Time limit while waiting for input ?
I have some doubts about your modification, perhaps you have some noise entering the system, or the limit switch is "bouncing"
Quote:
IF limup = 0 OR RUN_COUNT =>0 THEN
low blue
low up
ENDIF
firstly operator precedence make this If test dodgy, parentheses ensure correct result
IF (limup = 0 ) OR (RUN_COUNT =>0) THEN
secondly
since pbp vars are unsigned , this will always be true it can only be 0 or greater
since the run_count test always tests true the if statement is always true
thirdly
the while loop will only exit if limup is 0 or run_count is 0 , the statement is or should be redundant
