How to post Code

Quick question, how do I post code within the window on the forum, I have looked on the the site, but I can't find it, I am sure it is very simple to do.

Thanks,
Terry

At the bottom of each thread, there is a "Posting Permissions" box.
In there you'll see a "BB code" link.

That page shows all the different things you can do in a post on the forum.
The one you want is "Code".

HTH,

Once you click on the reply button you will want to click on the Go Advanced button.
Then you should see a tool bar above the editor box. The "#" will give you the code tags.
You will also want to click the upper left button of the tool bar to go into source mode, it works better than WYSIWYG.

Good place to see if my code posts properly. I've seen some have problems with %.

Code:

---

'****************************************************************
'*  Name    : LAB X1 16F877 Timer Interrupt.BAS                *
'*  Author  : Demon                                      *
'*  Notice  : Copyright (c) 2012                                *
'*          : All Rights Reserved                              *
'*  Date    : 2012-01-06                                        *
'*  Version : 1.0                                              *
'*  Notes  : PIC Basic Pro v2.60C                              *
'*          : MicroCode Studio Plus v2.2.1.1                    *
'*          : MPASM v3.50                                      *
'*          : Lab X1 Experimental Board                        *
'*          : MeLabs U2 Programmer v4.32                        *
'****************************************************************
'define  LOADER_USED 1

' Comment out CONFIG in MPASM include (File: 16F877.INC in PBP folder).
@ __config _HS_OSC & _WDT_OFF & _PWRTE_ON & _BODEN_ON & _LVP_OFF & _CPD_OFF & _WRT_ENABLE_OFF & _DEBUG_OFF & _PWRTE_OFF

define  OSC 20

DEFINE  LCD_DREG      PORTD        ' Set LCD data port
DEFINE  LCD_DBIT      0            ' Set starting data bit
DEFINE  LCD_RSREG    PORTE        ' Set LCD register select port
DEFINE  LCD_RSBIT    0            ' Set LCD register select bit
DEFINE  LCD_EREG      PORTE        ' Set LCD enable port
DEFINE  LCD_EBIT      1            ' Set LCD enable bit
DEFINE  LCD_BITS      8            ' Set LCD bus size
DEFINE  LCD_LINES    2            ' Set number of lines on LCD
define  LCD_COMMANDUS 2000          ' Set command delay time in microseconds
DEFINE  LCD_DATAUS    50            ' Set data delay time in microseconds

    TRISD = %00000000              ' Set all port D pins to output
    TRISE = %00000000              ' Set all port E pins to output

    ADCON1 = 7                      ' A/D off, all digital

wsave  VAR BYTE    $70 SYSTEM      ' Required by Instant Interrupt routine

    PAUSE  1000                    ' Wait for LCD to initalize
    LCDOUT  $FE,1,"LabX1 16F877 Tim Int"

'---[INT - interrupt includes]--------------------------------------------------
INCLUDE "DT_INTS-14.bas"    ; Base Interrupt System
INCLUDE "ReEnterPBP.bas"    ; Include if using PBP interrupts
INCLUDE "Elapsed_INT.bas"    ; Elapsed Time interrupts

'---[INT - interrupt definition]------------------------------------------------
ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
        INT_Handler  TMR1_INT,  _ClockCount,  PBP,  yes
    endm
    INT_CREATE            ; Creates the interrupt processor
ENDASM

@  INT_ENABLE  TMR1_INT  ; Enable Timer 1 Interrupts 

    GOSUB ResetTime          ' Reset Time to  0d-00:00:00.00
    GOSUB StartTimer          ' Start the Elapsed Timer

Main:
    IF SecondsChanged = 1 THEN 
        SecondsChanged = 0
        LCDOUT $FE,$C0, DEC Days,"d-",DEC2 Hours,":",DEC2 Minutes,":",DEC2 Seconds
    ENDIF
    GOTO Main

    end

---

WOOT! It worked!

Robert
:)