Multi timer interrupt question

I'm going to use Darrel Taylor's interrupt program and want to run 2 separate timers. So when input 1 is on the timer starts and runs and can be reset. While it's timing I want to turn different lights on/off depending on how long the input has been on.

I then want to do the same with a second input.

I'm looking through all the paperwork (trying to RTFM) and I see the Gosub ResetTime and Gosub StartTimer commands. This is from the "Timers, Clocks, RTC's: Elapsed Timer Demo"

And I also see from Darrel's page that there are up to 4 timers in the Elapsed.bas.

What are the commands to start and reset the individual timers?

I've been searching the forum and Darrel's site and haven't seen or have overlooked this information.

Thank you,
Hylan

I'm trying to start with just getting one timer to work and do the usual "Flash an LED", or actually toggle between 2 LED's so I can tell where in the timing sequence it is. With what I have below, LED2 is on at startup and then it switches to LED1 and never toggles again. I think I have something wrong in my setup but don't know what. Once I get this working I would like to add the TMR1 (TimerB).

Any help is appreciated.
Thank you,
Hylan
Here's the code:

Code:

---

'****************************************************************
'*  Name    : TimerTest.BAS                                      *
'*  Author  : [select VIEW...EDITOR OPTIONS]                    *
'*  Notice  : Copyright (c) 2012 [select VIEW...EDITOR OPTIONS] *
'*          : All Rights Reserved                              *
'*  Date    : 12/9/2012                                        *
'*  Version : 1.0                                              *
'*  Notes  :                                                  *
'*          :                                                  *
'****************************************************************
#config
 __CONFIG _CONFIG1H, _OSCS_OFF_1H & _OSC_XT_1H
 __CONFIG _CONFIG2L, _BOR_ON_2L & _BORV_27_2L & _PWRT_ON_2L
 __CONFIG _CONFIG2H, _WDT_OFF_2H & _WDTPS_128_2H
 __CONFIG _CONFIG3H, _CCP2MUX_OFF_3H
 __CONFIG _CONFIG4L, _LVP_OFF_4L
#endconfig
'**************************************************************
'Interrupt code added 12-9-12
INCLUDE "DT_INTS-18.bas"    ; Base Interrupt System
INCLUDE "ReEnterPBP-18.bas"    ; Include if using PBP interrupts
INCLUDE "Elapsed_INT-18.bas"  ; Elapsed Timer Routines


ASM
INT_LIST  macro    ; IntSource,        Label,  Type, ResetFlag?
        ;INT_Handler    RX_INT,    _serialin,  PBP,  no       
        ;INT_Handler    INT_INT,  _ToggleLED1,  PBP,  yes
        INT_Handler  TMR0_INT,  _TimerA,  PBP,  yes
        ;INT_Handler  TMR1_INT,  _TimerB,  PBP,  yes
    endm
    INT_CREATE                ; Creates the interrupt processor
ENDASM

T0CON  = %10010010            ; T0 = 16-bit, Prescaler 8
;@  INT_ENABLE  RX_INT    ; enable external (INT) interrupts 
;@    INT_ENABLE  INT_INT    ; enable external (INT) interrupts
@    INT_ENABLE  TMR0_INT    ; enable Timer 0 interrupts
;@    INT_ENABLE  TMR1_INT    ; Enable Timer 1 Interrupts 

CLEAR  ' Clear all variables to 0

LED1        VAR PortC.5    ' Output 1
LED2        VAR PortC.4     
IN1        VAR PortE.0    ' Input 1
Counter    var byte        ' Keeps count of seconds
                 
PortA  =  %00100000      ' PortA All Off
PortB  =  %00000000      ' PortB All Off
PortC  =  %00000000      ' PortC All Off
PortD  =  %00000000      ' PortD All Off
PortE  =  %00000000      ' PortE All Off
PortF  =  %00000000      ' PortF All Off
PortG  =  %00000000      ' PortG All Off
TRISA  =  %00011001      ' Inputs = 1, Outputs = 0 RA(7-6) NA
TRISB  =  %11111111      ' Inputs = 1, Outputs = 0
TRISC  =  %10000010      ' Inputs = 1, Outputs = 0
TRISD  =  %11111111      ' Inputs = 1, Outputs = 0
TRISE  =  %11111111      ' Inputs = 1, Outputs = 0
TRISF  =  %11111111      ' Inputs = 1, Outputs = 0
TRISG  =  %00000000      ' Inputs = 1, Outputs = 0 RG(7-5) NA
ADCON0  =  %00000001      ' A/D Enabled, Channel 0 (AN0)
ADCON1  =  %00001110      ' AN0 Analog Input (Rest Digital I/O)
ADCON2.7 = 1                ' Right Justify 10 Bit Word
CMCON  =  %00000111      ' Both Comparators Disabled
INTCON2.7 = 0              ' Turn ON PortB Pull-Ups
T1CON  =  %00110100      ' 1:8 Prescale, T1OSCEN Off (524.288mS)

GOSUB ResetTime              ; Reset Time to  0d-00:00:00.00   
GOSUB StartTimer              ; Start the Elapsed Timer

Main:
pause 200
if (Counter > 0) and (Counter < 10) then
LED1 = 1
LED2 = 0
else
LED1 = 0
LED2 = 1
endif

goto Main

TimerA:
if SecondsChanged = 1 then
    SecondsChanged = 0
    Counter = Counter + 1
        If Counter = 20 then
        Counter = 0
        endif
endif                           
@ INT_RETURN

---

Hylan,

The Elapsed Timer only works with Timer1.
And there is only one Elapsed Timer.
That's not to say you couldn't write a program to do multiple Elapsed Timers.

The INT_HANDLER for TMR1_INT has to point to the _ClockCount routine in the include file.

Code:

---

        INT_Handler  TMR1_INT,  _ClockCount,  PBP,  yes

---