• Recent Forum Posts

Re: MCP3201 problems

Hello Fratello,

Sounds like a hardware issue. I worked with LM2931 and i had some strange problems because I used a lower capacitance on output. Connect a 100uF (0,1uF is too low) near the stab...

midali Yesterday, 22:56

Re: how to calculate reverse value with scale

Ohhh yes yes ! I'm so tired... didn't saw as simple as it is !
Regards

harryweb Yesterday, 15:31

Re: how to calculate reverse value with scale

or

should do it. Where I assume you are reading 130 to 30.

Thus, a reading of 130 will give output = 0
and a reading of 30 will give output = 100

richard Yesterday, 02:10

Re: how to calculate reverse value with scale

should do it. Where I assume you are reading -130 to +30.

Thus, a reading of -130 will give output = 0
and a reading of +30 will give output = 100

Jerson Yesterday, 01:59

how to calculate reverse value with scale

Hi,

I cannot find how to convert my level value from receiver (from -130dBm to -30dBm) I do not use minus -> so 130 to 30
My display (nextion type) has a "vu meter" witch needs 0 to 100
When...

harryweb - 10th December 2017, 23:22

Re: problem with LCD large Numbers

ozarkshermit, Attached is a program I wrote quite a few years ago to test the theory of using BIG numbers on a 4 x 20 LCD display. Enjoy...

Dave - 10th December 2017, 21:52

Re: problem with LCD large Numbers

Richard:

Thanks for your response. I modified your program to use with a 18F14K22, and since I have a serial LCD backpack, I changed the LCD stuff to SEROUT2. Also, no PB3 here, still on 2.6,...

ozarkshermit - 10th December 2017, 15:49

Re: problem with LCD large Numbers

I can't quite see why the pgm misbehaves like you mention ,. but I will make these comments

peek/poke is the least efficient way to use progmem, it only stores 1 byte per every word of...

richard - 10th December 2017, 06:48

problem with LCD large Numbers

Hi all
I have been away for a LOONG time, finally getting back working with PICs.

I have developed a program to display large numbers on a 4x20 LCD, using PBP 2.6. The PIC is an 18F14K22.
I...

ozarkshermit - 9th December 2017, 21:52

Re: Addressable RGB LED's & LED strips

you can use the digital strips with the built-in programs,
most digital led controllers can support the ws2812,sk6812 led,
or the Remote controller with program inside,it is much easy,
also the...

PhilXu007 - 9th December 2017, 07:52
• mister_e

by Published on - 25th February 2012 13:49

Here's a simple INCLUDE file wich allow to scan any matrix KeyPad format on any PORT you decide. Yeah i know, a bit code ...

[Beginner Tutorial] How to get started with PICBASIC PRO Demo, MicroCode Studio & PICKIT 2

by Published on - 26th June 2011 16:15  Number of Views: 3878

So you're new to PBP and want a simple step-by-step guide? This one will show how how to get started with
• PicBasic
...

[Beginner Tutorial] How to get started with PICBASIC PRO Demo, MPLAB & PICKIT 2

by Published on - 23rd June 2011 21:52  Number of Views: 3990

So you're new to PBP and want a simple step-by-step guide? This one will show how how to get started with
• PICBASIC
...

New PIC Utility. PICMultiCalc

by Published on - 28th April 2011 05:17

Hi all,
Few times ago i did this little utility to help in Timer, Usart, Eusart and PWM calc. It have been tested ...

Beginner's stack of FAQ... to solve stack of facts?

by Published on - 5th December 2010 17:58  Number of Views: 3774

Hi,
Here's a short list of Frequently Asked Questions that should be of interest for most beginners. Don't hesitate to read them... they're not going to bite you
...

cheap touch sensor

by Published on - 25th June 2010 17:00  Number of Views: 6645

Hi all! Even if there's some built-in solution and dedicated IC to do the job, here's my few cents solution. Not that ...

by Published on - 15th June 2010 11:34  Number of Views: 2560

Here's a simple INCLUDE file wich allow to scan any matrix KeyPad format on any PORT you decide. Yeah i know, a bit code ...

USBDemo, something to learn USB a little bit

by Published on - 30th May 2010 23:24  Number of Views: 2876

Hi all,
Since the USB stuff is coming more and more popular, and as we see more and more questions, i decided to ...

New PIC Utility. PICMultiCalc

by Published on - 21st May 2010 14:37  Number of Views: 3713

Hi all,
Few times ago i did this little utility to help in Timer, Usart, Eusart and PWM calc. It have been ...