flotulopex
- 3rd February 2021, 20:06
Hi All,
As HSERIN and HSEROUT are working well on my 18F1220, I can't make DEBUGIN work (DEBUG is okay).
I couldn't find any information searching in the forum and googeling around so if somebody has a clue where I'm missing something...
@ __CONFIG _CONFIG1H, _IESO_OFF_1H & _FSCM_OFF_1H & _INTIO1_OSC_1H ; OSC1 as RA7, OSC2 as RA6
@ __CONFIG _CONFIG2L, _BORV_27_2L & _BOR_OFF_2L & _PWRT_OFF_2L
@ __CONFIG _CONFIG2H, _WDT_OFF_2H & _WDTPS_32K_2H
@ __CONFIG _CONFIG3H, _MCLRE_OFF_3H
@ __CONFIG _CONFIG4L, _DEBUG_OFF_4L & _LVP_ON_4L & _STVR_ON_4L
@ __CONFIG _CONFIG5L, _CP0_OFF_5L & _CP1_OFF_5L
@ __CONFIG _CONFIG5H, _CPB_OFF_5H & _CPD_OFF_5H
@ __CONFIG _CONFIG6L, _WRT0_OFF_6L & _WRT1_OFF_6L
@ __CONFIG _CONFIG6H, _WRTC_OFF_6H & _WRTB_OFF_6H & _WRTD_OFF_6H
@ __CONFIG _CONFIG7L, _EBTR0_OFF_7L & _EBTR1_OFF_7L
@ __CONFIG _CONFIG7H, _EBTRB_OFF_7H
OSCCON = %01110000 'set INTRC to 8 MHZ
OSCTUNE = %00000000 'OSCILLATOR TUNING REGISTER
ADCON0 = %00000000 'A/D CONTROL REGISTER 0
ADCON1 = %00000000 'A/D CONTROL REGISTER 1
ADCON2 = %00000000 'A/D CONTROL REGISTER 2
INTCON = %00000000 'INT CTRL REG
INTCON2 = %00000000 'INT CTRL REG 2
INTCON3 = %00000000 'INT CTRL REG 3
PORTA = %00000000 'State High (1) or Low (0)
TRISA = %00000000 'Data Direction Control Register (Input/Output)
PORTB = %00000000 'State High (1) or Low (0)
TRISB = %00010000 'Data Direction Control Register (Input/Output)
Define OSC 8 ' Oscillator speed in MHz: 3(3.58) 4 8 10 12 16 20 24 25 32 33 40
DEFINE HSER_CLROERR 1 ' Clear overflow automatically
DEFINE NO_CLRWDT 1 ' Don't waste cycles clearing WDT
DEFINE DEBUG_REG PORTB
DEFINE DEBUG_BIT 1
DEFINE DEBUG_BAUD 9600
DEFINE DEBUG_MODE 0
DEFINE DEBUGIN_REG PORTB
DEFINE DEBUGIN_BIT 4
DEFINE DEBUGIN_MODE 0
SData VAR BYTE(5)
TimeOut CON 100
MAIN:
' Send some serial data with ID as header from Serial Comm Terminal
DEBUGIN TimeOut,MAIN,[WAIT("ID"),str SData\5]
' Display received data
DEBUG str SData\5 ,13
GOTO MAIN
END
As HSERIN and HSEROUT are working well on my 18F1220, I can't make DEBUGIN work (DEBUG is okay).
I couldn't find any information searching in the forum and googeling around so if somebody has a clue where I'm missing something...
@ __CONFIG _CONFIG1H, _IESO_OFF_1H & _FSCM_OFF_1H & _INTIO1_OSC_1H ; OSC1 as RA7, OSC2 as RA6
@ __CONFIG _CONFIG2L, _BORV_27_2L & _BOR_OFF_2L & _PWRT_OFF_2L
@ __CONFIG _CONFIG2H, _WDT_OFF_2H & _WDTPS_32K_2H
@ __CONFIG _CONFIG3H, _MCLRE_OFF_3H
@ __CONFIG _CONFIG4L, _DEBUG_OFF_4L & _LVP_ON_4L & _STVR_ON_4L
@ __CONFIG _CONFIG5L, _CP0_OFF_5L & _CP1_OFF_5L
@ __CONFIG _CONFIG5H, _CPB_OFF_5H & _CPD_OFF_5H
@ __CONFIG _CONFIG6L, _WRT0_OFF_6L & _WRT1_OFF_6L
@ __CONFIG _CONFIG6H, _WRTC_OFF_6H & _WRTB_OFF_6H & _WRTD_OFF_6H
@ __CONFIG _CONFIG7L, _EBTR0_OFF_7L & _EBTR1_OFF_7L
@ __CONFIG _CONFIG7H, _EBTRB_OFF_7H
OSCCON = %01110000 'set INTRC to 8 MHZ
OSCTUNE = %00000000 'OSCILLATOR TUNING REGISTER
ADCON0 = %00000000 'A/D CONTROL REGISTER 0
ADCON1 = %00000000 'A/D CONTROL REGISTER 1
ADCON2 = %00000000 'A/D CONTROL REGISTER 2
INTCON = %00000000 'INT CTRL REG
INTCON2 = %00000000 'INT CTRL REG 2
INTCON3 = %00000000 'INT CTRL REG 3
PORTA = %00000000 'State High (1) or Low (0)
TRISA = %00000000 'Data Direction Control Register (Input/Output)
PORTB = %00000000 'State High (1) or Low (0)
TRISB = %00010000 'Data Direction Control Register (Input/Output)
Define OSC 8 ' Oscillator speed in MHz: 3(3.58) 4 8 10 12 16 20 24 25 32 33 40
DEFINE HSER_CLROERR 1 ' Clear overflow automatically
DEFINE NO_CLRWDT 1 ' Don't waste cycles clearing WDT
DEFINE DEBUG_REG PORTB
DEFINE DEBUG_BIT 1
DEFINE DEBUG_BAUD 9600
DEFINE DEBUG_MODE 0
DEFINE DEBUGIN_REG PORTB
DEFINE DEBUGIN_BIT 4
DEFINE DEBUGIN_MODE 0
SData VAR BYTE(5)
TimeOut CON 100
MAIN:
' Send some serial data with ID as header from Serial Comm Terminal
DEBUGIN TimeOut,MAIN,[WAIT("ID"),str SData\5]
' Display received data
DEBUG str SData\5 ,13
GOTO MAIN
END