longpole001
- 13th May 2015, 10:25
Hi Guys
had need to review the SPI flash routines to incorporate the 4kb/32kb/64kb erase support and other features offered by the WINBOND series of flash chips
this is a re- vamp of the code i did last year and i posted for the 8mb chip to support another flash chip manufacture
hope you find it of use and dont have to re do the code wheel - again
this should be as an include to your main code
regards
Sheldon
'* : All Rights Reserved *
'* Date : 4/05/2015 *
'* Version : 2.0 *
'* Notes : Rewriten for Winbond SPI W25Q series Serial NOR Flash chips .. *
'* : W25Q32 - 32Mbit(4MB) *
'* : --- Orginal code (V1.1) based on support for M25P80 8Mbit chip or simular *
'* : no support of duel / quad SPI & QPI options *
'* : No support for Fast Write ( W25Q80 ) *
'* : NO support of Suspend write/read operations *
'* : chips are 3.3v - NOT 5V input tollerant *
'* : Code supports ..... *
'* : 1 Software Protection of data , hardware WP and Hold pins high *
'* : 2. 4KB sectors , 32/64KB blocks, for protection / erasing, copy commnads *
'* : 3. Manufacture ID /Chip size detection / selection for number of blocks *
'* : 4. Copy commands reseved use of scratch pad area of Block 0 *
'* : code does not need Longs to be enabled to save on code space *
'************************************************* ****************************************
' *
' Operational Notes on Timing Max and Min times *
' ============================================= *
' *
' 1. powerup delay to CE & WR = 5ms min *
' 2. 256 bytes max per read / write *
' 3. spi bus (mode 3) (clock idle High) and flash CE configures in main program *
' 4. avg is 20ma during write /25ma for erase, 15ma for read *
' 5. min 50ns on CE deselect *
' 6. SPI chip interface timing has min of 5ns requirements , so no timing issues *
' for picbasic which has a min of 2us using shiftout cmd *
' 7. software reset via spi = min 30us - BUSY & SUS bits are checked before issue *
' 8. sector erase (4KB)= min 45mS max 400ms, *
' 9. block Erace(32KB) = min 120ms max 1.6sec *
' 10. Block Erase (64KB)= min 150ms max 2.0sec *
' 11. Chip Erase(32Mbit)=min 10sec max 50sec *
' 12. hold/reset pin - factory dephalt is hold *
' 13. WP pin is not active - SRP1=0 , SRP0 =0 - FACTORY DEPHALT *
' 14. 25QxxIQ has QE bit in register 2 = 1 from factory and cannot be cleared *
'----------------------------------------------------------------------------------------*
'---------- Winbond SPI FLASH (W25Q series) commands set --------------------------------
' NOTE: No support for DUAL/QUAD/ QPI instruction sets
'
' SDC_cmd, SDC_CmdCode
' command 1-13 use the Write enable command ---
Flash_Wr_reg1 con 1 ' $01 'def write the Status Register 1(S7-S0) - 1 byte data - write enable req prior
Flash_Wr_reg2 con 2 ' $31 'def write the Status Register 2(S15-S8) - 1 byte data - write enable req prior
Flash_Wr_reg3 con 3 ' $11 'def write the Status Register 3(S23-S16) - 1 byte data - write enable req prior
Flash_WR con 4 ' $02 'def Page Program mode command ( 24bit address req)+ (1 byte data)- write enable req prior
Flash_Wr_Secreg con 5 ' $42 'def Program Security Register write ( 24bit address req)+ (1 byte data)- write enable req prior - holds access upto 256byte data per register
Flash_Sec_Ers con 6 ' $20 'def Sector Erase command (4KB) ( 24bit address req) - write enable req prior
Flash_Blk32_Ers con 7 ' $52 'def Block 32KB Erase Command (32KB) ( 24bit address req) - write enable req prior
Flash_Blk64_Ers con 8 ' $D8 'def Block 64KB Erase Command (64KB) ( 24bit address req) - write enable req prior
Flash_Indv_Blk_LCK CON 9 ' $36 'def Indervidual Block/Sector Lock ( 24bit address req): WEP must be 1 to setup and use - write enable req prior
Flash_Indv_Blk_UNLCK CON 10 ' $39 'def Indervidual Block/Sector UNLock ( 24bit address req): WEP must be 1 to setup and use - write enable req prior
Flash_Secreg_Ers con 11 ' $44 'def Erase Program Security Register ( 24bit address req) - write enable req prior
Flash_Bulk_Ers con 12 ' $C7 'def Bulk Erase command - write enable req prior
Flash_Globe_LCK con 13 ' $7E 'def Globel Block /Sector Lock : WEP must be 1 to setup and use - write enable req prior
Flash_Globe_UNLCK con 14 ' $98 'def Globle Block/Sector Unlock : WEP must be 1 to setup and use - write enable req prior
' commands 14-12 use the Read command ---
Flash_RD con 15 ' $03 'def read data at normal speed ( 24bit address req)+ (1 byte data)
Flash_Rd_HS con 16 ' $0B 'def read data at High speed (Fast Read) ( 24bit address req)+ (1dummy+1 byte data)
Flash_Rd_Secreg con 17 ' $48 'def Program Security Register read ( 24bit address req)+ (1 dummy +1 data)( simular to fast read command )
Flash_Rd_Sig con 18 ' $4B 'def read Flash device Unique ID signature - cmd + 4 dummy bytes , returns 64bit ID MSB first
Flash_Rd_Blk_LCK con 19 ' $3D 'def Read Block/Sector Lock status , returns 0= unlocked 1= Locked ( 24bit address req)+ (1 byte data)
Flash_Rd_ID con 20 ' $9F 'def Read manufacture 1byte/device/UID code 2 bytes ( JEDEC ID) - returns 3 bytes
Flash_Rd_reg2 con 21 ' $35 'def read the Status Register 2(S15-S8) - returns 1 data byte
Flash_Rd_reg3 con 22 ' $15 'def read the Status Register 3(S23-S16) - returns 1 data byte
'---- not in command lookup table - used directly -----
Flash_Wr_dis CON $04 'def write disable command
Flash_Rd_reg1 con $05 'def read the Status Register 1(S7-S0) - done by Bsy_chk routine
Flash_Wr_en con $06 'def write Enable command
Flash_Vol_Wr_EN con $50 'def Volatile SR Write Enable - used to change write_reg1 bits but wont set WEL flag - quick way of changeing register for protection bits ( no write enable
Flash_EN_Rst con $66 'def Enable Software Reset - reset takes min 30us
Flash_Rst Con $99 'def Do a Reset - Must be combined with Flash_EN_Rst
Flash_PWR_Dwn con $B9 'def Deep Power Down command
Flash_PWR_Up con $AB 'def Release From Deep Power Down command
' ---------- FLASH varables -------------------------
Data_Length var byte ' table of data length
SDC_buffer Var Byte[256] ' indexed data - max 256 bytes - 8mb FLASH has a 256 Limit from page Writes - Note 512 used in SD routines
SDC_data_in Var Byte ' Data in byte from flash
SDC_data_out Var Byte ' Data out byte from Flash -
SDC_address_High Var word ' address higher word sent to FLASH
SDC_address_Low Var word ' address lower word sent to FLASH
SDC_index Var Word ' Loop index counter
SDC_CmdCode Var Byte ' used here as Sector protect value for the Write Status register
SDC_cmd Var Byte ' command code for selected operation
SDC_Block var Byte ' 64K block Address - uses SDC_address_High.low , each block 0-63(32Kbit) 0-127(64Kbit), addressing used both
SDC_Sector var byte ' 4K Sector address - uses SDC_address_Low.highbyte , each sector = 16 pages , so sector 0 = page 0-15 - values = 0 -15
SDC_Page var byte ' Page Address
SDC_Byte Var byte ' Bytes Address
Flash_RD_Fast var bit ' Flag for High speed read 1 = Highspeed read speed 0= normal read speed
Flash_Install var bit ' flag set when flash install program used
Flash_32KB_Block_Sel var bit ' Sets StartPage address for 32KB Block erase - 0 = lower block - sets start page address - page 0 - 127, 1 = High block - page 128 - 256
Flash_Protect var bit ' Set Protect =1 / Unprotect =0 of a block , used as a read of block status as well
Flash_Blk_Orgin var byte ' Orgin sector value - copy sector command
Flash_Blk_Dest var byte ' destination sector value - copy Sector Command
Flash_Sec_Orgin var byte ' Orgin sector value - copy sector command
Flash_Sec_Dest var byte ' destination sector value - copy Sector Command
Flash_Page_Orgin var byte ' Orgin Page value
Flash_Page_Dest var Byte ' Dest Page Value
Flash_Page_Length var byte ' number of pages
Flash_Clear var bit ' flag to clear orginal sector 1= clear
Flash_Manf_id var byte ' manufacture id code
Flash_Manf_type var byte ' device type code
Flash_Manf_cap var byte ' device capacity code
Flash_tmp var byte ' used as a temp varable
Flash_tmp2 VAR BYTE ' used as a temp varable
Flash_Reg_val var byte ' Flash register value
Flash_Addr_Copy_Low var word ' low word temp storage of input address and data length
Flash_Addr_Copy_High var word ' high word temp storage of input address and data length
'----------- Varable settings at startup ---------------------------------------------
Flash_RD_Fast = 0 ' Set to normal read at start
Flash_Install = 0 ' set to 0 when flash install not being used
Flash_Clear = 0 ' set not to clear
Flash_32KB_Block_Sel = 0 ' set to use low address
'---------------- Routines ------------------
goto JumpOverSPIFLASH ' Jump to end of this include file for Correct compile
Flash_Init:
' do a read register command to clear the Flash register after power up
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_Rd_reg1 ' Send the read status register command byte
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
gosub buffer_clear ' clear varables area
return
' -----------------------------
Buffer_Clear:
For SDC_index = 0 To 255
SDC_buffer[SDC_index] = 0
next SDC_index
return
'---------------------------------------
Flash_Reset:
' routine to software reset the flash
' enable reset and reset must be consecutive
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_EN_Rst ' Send Enable Reset command
gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
SDC_data_out = Flash_Rst ' Send Reset command
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'-----------------------------------------
Flash_Format:
'Note wont work if any sectors are protected
' can take upto 50sec on 32mbit chip
sdc_cmd = Flash_Bulk_ers ' excutes as it sounds
gosub Flash_Comand
return
'-------------------------------------------------
Flash_Sec_Erase:
' assumes Block address 0-63
' assumes Sector value 0 -15
' erases 1 Sector at a time address (4KB)= 15 pages
' Erases wont work on sectors that are write protected
' sector erase take 400ms per instruction
SDC_pAGE = 0 ' ensure 0
SDC_pAGE = sdc_SECTOR << 4 ' shift given sector 0-15 to upper page value
sdc_cmd = Flash_Sec_Ers ' Erases sector ( 256 pages x 256 bytes )
SDC_address_high.byte0 = SDC_Block ' set sector Address 0 to 15 for chip
SDC_address_low.byte1 = SDC_Page ' set page start address 0 to 255
SDC_address_low.byte0 = 0 ' set byte start address 0 to 255
gosub Flash_Comand ' Do the command
return
'----------------------------------------------------
Flash_Blk32_Erase:
' assumes Block address
' assumes flag 32KB_Block_Sel 0 = bottom 32Kb start address page, 1= 128page address
' erases 1/2 a 64KB Block at a time address (32KB)= 128 pages
' Erases wont work on sectors that are write protected
' sector erase take min 120ms max 1.6Sec per instruction
IF Flash_32KB_Block_Sel = 0 THEN ' select offset page for 32 byte sector
SDC_PAGE = 0
ELSE
SDC_PAGE = 128
ENDIF
sdc_cmd = Flash_blk32_Ers ' Erases 32kB block ( 128 pages of 256 bytes )
SDC_address_high.byte0 = SDC_Block ' set block Address for chip
SDC_address_low.byte1 = SDC_PAGE ' set page start address 0 to 255
SDC_address_low.byte0 = 0 ' set byte start address 0 to 255
gosub Flash_Comand ' Do the command
return
'-------------------------------------------------------------
Flash_Blk64_Erase:
' assumes Block address
' erases a 64KB Block at a time address (64KB)= 256 pages
' Erases wont work on sectors that are write protected
' sector erase take min 160ms max 2.0Sec per instruction
sdc_cmd = Flash_blk64_Ers ' Erases 64kB block ( 256 pages of 256 bytes )
SDC_address_high.byte0 = SDC_Block ' set Block Address for chip
SDC_address_low.byte1 = 0 ' set page start address 0 to 255
SDC_address_low.byte0 = 0 ' set byte start address 0 to 255
gosub Flash_Comand ' Do the command
return
'------------------------------------------------------------------
Flash_Block_Copy:
' copys data from 1 block to another
' erases destination block - optional clean of orginal block
' assumes Flash_Sect_Orgin,Flash_Sect_Dest ,Flash_clear
' Erases wont work on blocks that are write protected
' block erase take 400ms per instruction
SDC_Block = Flash_Blk_Dest ' clear destination block
gosub Flash_blk64_Erase ' use SDC_blk64_erase info to erase destination sector
for SDC_PAGE = 0 to 255 ' copy pages to selected block ( 256bytes at a time)
SDC_Block = Flash_blk_Orgin ' block to copy
SDC_byte = 0
Data_Length = 255
gosub Flash_Read ' read the data to buffer
SDC_Block = Flash_Blk_Dest ' block to copy to
SDC_byte = 0 ' use block details for destination
Data_Length = 255
gosub Flash_Write ' write the data
next SDC_PAGE
if Flash_clear = 1 then
SDC_Block = Flash_Blk_Orgin ' clean up orgin Block
gosub Flash_Blk64_Erase
endif
return
Flash_Page_Copy:
' copys data from pages 0 -255 from orgin or destination block
' assumes destination block pages are Erased
' assumes pages orgin and pages destination do not cross block boundrys
' assumes Flash_Page_Orgin,Flash_Page_dest ,Flash_Page_length, Flash_blk_orgin ,Flash_blk_dest
' writes wont work on blocks that are write protected
for Flash_tmp2 = Flash_Page_Orgin to Flash_Page_length ' copy sector 0 pages to selected sector 0 ( 256bytes at a time)
SDC_Block = Flash_blk_Orgin ' sector to copy
SDC_PAGE = Flash_tmp2
SDC_byte = 0
Data_Length = 255
gosub Flash_Read ' read the data to buffer
SDC_Block = Flash_blk_Dest ' sector to copy to
SDC_PAGE = Flash_Page_Dest ' page to copy to
SDC_byte = 0
Data_Length = 255
gosub Flash_Write ' write the data
Flash_Page_Dest = Flash_Page_Dest + 1 ' increment destination page
next Flash_tmp2
return
'----------------------------------------
Flash_Write:
' assumes data length , address and upto 256 bytes in SDC_buffer[] to send
' writes bytes from SDC_buffer[] into flash , block/page/byte loction must be "FF" at start
' write wont work on sectors that are write protected
sdc_cmd = Flash_WR ' excutes as it sounds - max of 256 bytes
SDC_address_high.byte0 = SDC_Block ' set block Address for chip
SDC_address_low.byte1 = SDC_Page ' set page start address 0 to 255
SDC_address_low.byte0 = SDC_byte ' set byte start address 0 to 255
gosub Flash_Comand
return
'--------------------------------------
Flash_Read:
' assumes Block, page, bytes , data length input
' gets upto bytes data into SDC_buffer[] from flash
' uses normal read speed if no Flash_RD_Fast flag set
if Flash_RD_Fast = 1 then
sdc_cmd = Flash_Rd_HS ' excutes fast read - max of 256 bytes
else
sdc_cmd = Flash_RD ' excutes normal read - max of 256 bytes cos of buffers size/ page size
endif
SDC_address_high.byte0 = SDC_Block ' set block Address for chip
SDC_address_low.byte1 = SDC_Page ' set page start address 0 to 255
SDC_address_low.byte0 = SDC_byte ' set byte start address 0 to 255
gosub Flash_Comand
return
Flash_WR_protect:
' routine to protect/ unprotect a set block of 60-63 in 32kbit chip ( block 60-63 used by K9 system stored settings )
' Assumes Flash_Protect - 0 = unprotect 1 = Protect a sector
' SETUP FOR 32kB CHIP
' Bit7 = SRP0 - Set to 0 - software protect (SRP1= 0 DEPHALT(stat_reg2(bit0), not WP pin
' bits6(SEC) = 0 = 64KB Block 1= 4Kb SECTOR , Bit5(TB) 0= Top, 1 = Bottom , Bit4-2 = BP2-BP0. bits 1-0 (wel, busy )
if Flash_Protect = 0 then
SDC_buffer[0] = $00 ' clear all blocks
else
SDC_buffer[0] = $0C ' set blocks 60-63 protected for K9 project
endif
sdc_cmd = Flash_Wr_reg1 ' write register
data_length = 1 ' set 1 byte
gosub Flash_Comand
return
'-----------------------------------------------------------
Flash_WR_Disable:
' reset the write enable latch
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_Rd_reg1 ' Send the read status register command byte
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'----------------------------------------------------
Flash_Read_ID:
' returns JEDEC ID- returns Manufacture ID byte($EF), mem type - (ID15-ID8)1byte ,capacity(ID7-ID0)1byte)
sdc_cmd = Flash_Rd_ID ' Flash Read ID
data_length = 3 ' 3 bytes
gosub Flash_Comand
Flash_Manf_id = SDC_buffer[0]
Flash_Manf_type = SDC_buffer[1]
Flash_Manf_cap = SDC_buffer[2]
IF FLASH_Install = 1 then
HSEROUT ["Flash Manf ID = ",hex Flash_Manf_id," Flash Device ID = ",hex Flash_Manf_type," Device Capacity ID = ",hex Flash_Manf_cap,13,10]
endif
return
'---------------------------------------------------------------------
Flash_Read_Sig:
' returns the flash chips Unique ID number ( 64Bit)
sdc_cmd = Flash_Rd_Sig ' Flash Read Unique ID signature
data_length = 4 ' 4 bytes ' Flash Read Unique ID signature
gosub Flash_Comand
return
'----------------------------------------------
Flash_Read_BLK_Lock:
'routine to read block or sector locks ( WPS=1 to work )
sdc_cmd = Flash_Rd_Blk_LCK ' Flash Read block lock
data_length = 1 ' 1 bytes
gosub Flash_Comand
Flash_Protect = SDC_buffer[0] & $01 ' get bit0 value - 1 = locked .0 = unlocked
return
'---------------------------------------------
Flash_Power_Down:
' sEt Flash chip to low power mode from standby mode - no command other tha powerup will wake the device
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_PWR_Dwn ' command to pwr down
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'----------------------------
Flash_Power_Up:
' sEt Flash chip to standby mode - no command other tha powerup will wake the device
' sEt Flash chip to low power mode from standby mode - no command other tha powerup will wake the device
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_PWR_Up ' command to pwr up
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'-----------------------------
' -----------------------------
Flash_Read_reg2:
' reads write register 2 -
' Register 2 controls .....
' bit7(S15)- Suspend Status
' bit6(S14)CMP -Compliment Protect - dephalt CMP =0
' bit5-3(S13-11)- Security Register(One time programable) dephalt = 000
' bit1(S9) - QE - Quad SPI Mode Enable ( default =0 when chips NOT FVIQ type)
' bit0(S8) - SRP1- Protect bit1 _ dephalt =0
'
sdc_cmd = Flash_Rd_reg2 ' Flash Read register 2
data_length = 1 ' 1 bytes returned
gosub Flash_Comand
return
'---------------------------------------
Flash_Read_reg3:
' Register 3 controls .....
' bit7(S23) - Hold(0- dephalt)/Reset(1) pin fuction
' bit6,5(S22,S21)(0,0=100%),(0,1=75%),(1,0=50%),(1,1 =25%- dephalt) read driver strength- used to overcome cpacitive loading ,trace impendace issues with signal at high speed reads
' bits4,3 - reserved (writen as 0)
' Bit2(S18) WPS - selects Protection methode - Indervidual block/sectors(WPS=1) or by grouping range(WPS=0) ( WPS dephalt is 0 )
' Bits1,0-reserved(writen as 0)
sdc_cmd = Flash_Rd_reg3 ' Flash Read register 3
data_length = 1 ' 1 bytes returned
gosub Flash_Comand
return
'-----------------------------------
Flash_Comand:
' assumes SDC_address long
' assumbe data_Length = Lookup table to fill
' max 256 bytes per write
' erase of the sector by byte / bulk is needed prior to write , as a write only changes a 1 to 0 , and the erase chanse the 0 to 1
if SDC_cmd = 0 then return ' invalid command if value =0
Lookup SDC_cmd,[$00,$01,$31,$11,$02,$42,$20,$52,$D8,$36,$39,$44,$C 7,$7E,$98,$03,$0B,$48,$4B,$3D,$9F,$35,$15],SDC_CmdCode ' asignes command code to flash chip
Flash_tmp = 0 ' ensure 0 - counter for busychk loop
gosub BSY_chk ' do for all commands
if SDC_cmd <=14 then ' do for writes, sector erase,bulk erase , write reg protect - commands 1-14 use writen enable first
FLASH_CE = 0 ' Bring the FLASH chip select line low.
SDC_data_out = Flash_Wr_en ' Send command byte that requires a write
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high to complete the write command
pauseus 1 ' pause between prev command - may not need
endif
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = SDC_CmdCode ' Send the command byte,
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
if SDC_cmd =>4 and SDC_cmd <=11 or _ ' if write commands 4-11 then use 24bit address assigned
SDC_cmd =>15 and SDC_cmd <=19 then ' or read commands 15-19 then use 24bit address assigned , command 18 uses 24bit address as 3 dummy bytes
SDC_data_out = SDC_address_high.Byte0 ' set block Address for chip
Gosub Flash_spiw ' Write Byte SDC_data_out.
SDC_data_out = SDC_address_low.Byte1 ' set page address 0 to 255
Gosub Flash_spiw ' Write Byte SDC_data_out.
SDC_data_out = SDC_address_low.Byte0 ' set byte address 0 to 255
Gosub Flash_spiw ' Write Byte SDC_data_out.
if SDC_cmd => 16 and SDC_cmd <= 18 then ' if read High speed mode ,Program security read , Read Unique ID(add 4th dummy byte)
SDC_data_out = $00 ' add a dummy byte to command
Gosub Flash_spiw ' Write Byte SDC_data_out.
endif
endif
if SDC_cmd <=5 or _ ' if write commands require data bytes sent
SDC_cmd >=15 and SDC_cmd <= 22 then ' or read commands require data bytes returned
For SDC_index = 0 To Data_Length-1 ' DATA LENGTH -1 so byte 0 is counted when setting data length
if SDC_cmd <= 5 then ' if write ,Write register,write Security register then
SDC_data_out = SDC_buffer[SDC_index] ' send contents of indexed SDC_buffer
gosub Flash_SPIw ' write byte SDC_data_in from SPI bus. Returns SDC_data_in.
endif
if SDC_cmd =>15 and SDC_cmd <=22 then ' if read scommand returns data
gosub Flash_SPIR ' Read Byte SDC_data_in from SPI bus. Returns SDC_data_in.
SDC_buffer[SDC_index] = SDC_data_in
endif
Next SDC_index
endif
pauseus 1
FLASH_CE = 1 ' Bring the FLASH chip select line high.
return
'----------------------------------------------------
Bsy_chk:
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_Rd_reg1 ' Send the read status register1 command byte
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
Flash_tmp = 0 ' clear counter
while Flash_tmp <150 ' loop test read for busy ( counter may need to be increased depending on size of chip and time for block erase command to complete
gosub Flash_SPIR ' Read Byte SDC_data_in from SPI bus. Returns SDC_data_in.
IF FLASH_Install = 1 then
Flash_Reg_val = SDC_data_in ' get value of read status reg value for use in flash install program checks for protection
HSEROUT ["STATUS REG = ",hex Flash_Reg_val,13,10] ' show on terminal when doing flash install
HSEROUT ["Flash_tmp = ",dec2 Flash_tmp,13,10]
endif
Flash_tmp = Flash_tmp + 1
SDC_data_in = SDC_data_in & $01 ' mask bit 0 ( busy flag)
if SDC_data_in = 0 then Flash_tmp = 151 ' Test bit 0 if write not busy,force exit of loop
wend
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'-------------------------------
Flash_SPIR:
SO = 1 ' Shift out high bits while shifing in data.
Shiftin SO, SCK, 6,[SDC_data_in] ' MSb first, clock idle high.
Return
'-------------------------------
Flash_SPIW:
shiftout SI,SCK,5,[SDC_data_out] ' MSb first, clock idle high.
return
'------------------------
JumpOverSPIFLASH:
had need to review the SPI flash routines to incorporate the 4kb/32kb/64kb erase support and other features offered by the WINBOND series of flash chips
this is a re- vamp of the code i did last year and i posted for the 8mb chip to support another flash chip manufacture
hope you find it of use and dont have to re do the code wheel - again
this should be as an include to your main code
regards
Sheldon
'* : All Rights Reserved *
'* Date : 4/05/2015 *
'* Version : 2.0 *
'* Notes : Rewriten for Winbond SPI W25Q series Serial NOR Flash chips .. *
'* : W25Q32 - 32Mbit(4MB) *
'* : --- Orginal code (V1.1) based on support for M25P80 8Mbit chip or simular *
'* : no support of duel / quad SPI & QPI options *
'* : No support for Fast Write ( W25Q80 ) *
'* : NO support of Suspend write/read operations *
'* : chips are 3.3v - NOT 5V input tollerant *
'* : Code supports ..... *
'* : 1 Software Protection of data , hardware WP and Hold pins high *
'* : 2. 4KB sectors , 32/64KB blocks, for protection / erasing, copy commnads *
'* : 3. Manufacture ID /Chip size detection / selection for number of blocks *
'* : 4. Copy commands reseved use of scratch pad area of Block 0 *
'* : code does not need Longs to be enabled to save on code space *
'************************************************* ****************************************
' *
' Operational Notes on Timing Max and Min times *
' ============================================= *
' *
' 1. powerup delay to CE & WR = 5ms min *
' 2. 256 bytes max per read / write *
' 3. spi bus (mode 3) (clock idle High) and flash CE configures in main program *
' 4. avg is 20ma during write /25ma for erase, 15ma for read *
' 5. min 50ns on CE deselect *
' 6. SPI chip interface timing has min of 5ns requirements , so no timing issues *
' for picbasic which has a min of 2us using shiftout cmd *
' 7. software reset via spi = min 30us - BUSY & SUS bits are checked before issue *
' 8. sector erase (4KB)= min 45mS max 400ms, *
' 9. block Erace(32KB) = min 120ms max 1.6sec *
' 10. Block Erase (64KB)= min 150ms max 2.0sec *
' 11. Chip Erase(32Mbit)=min 10sec max 50sec *
' 12. hold/reset pin - factory dephalt is hold *
' 13. WP pin is not active - SRP1=0 , SRP0 =0 - FACTORY DEPHALT *
' 14. 25QxxIQ has QE bit in register 2 = 1 from factory and cannot be cleared *
'----------------------------------------------------------------------------------------*
'---------- Winbond SPI FLASH (W25Q series) commands set --------------------------------
' NOTE: No support for DUAL/QUAD/ QPI instruction sets
'
' SDC_cmd, SDC_CmdCode
' command 1-13 use the Write enable command ---
Flash_Wr_reg1 con 1 ' $01 'def write the Status Register 1(S7-S0) - 1 byte data - write enable req prior
Flash_Wr_reg2 con 2 ' $31 'def write the Status Register 2(S15-S8) - 1 byte data - write enable req prior
Flash_Wr_reg3 con 3 ' $11 'def write the Status Register 3(S23-S16) - 1 byte data - write enable req prior
Flash_WR con 4 ' $02 'def Page Program mode command ( 24bit address req)+ (1 byte data)- write enable req prior
Flash_Wr_Secreg con 5 ' $42 'def Program Security Register write ( 24bit address req)+ (1 byte data)- write enable req prior - holds access upto 256byte data per register
Flash_Sec_Ers con 6 ' $20 'def Sector Erase command (4KB) ( 24bit address req) - write enable req prior
Flash_Blk32_Ers con 7 ' $52 'def Block 32KB Erase Command (32KB) ( 24bit address req) - write enable req prior
Flash_Blk64_Ers con 8 ' $D8 'def Block 64KB Erase Command (64KB) ( 24bit address req) - write enable req prior
Flash_Indv_Blk_LCK CON 9 ' $36 'def Indervidual Block/Sector Lock ( 24bit address req): WEP must be 1 to setup and use - write enable req prior
Flash_Indv_Blk_UNLCK CON 10 ' $39 'def Indervidual Block/Sector UNLock ( 24bit address req): WEP must be 1 to setup and use - write enable req prior
Flash_Secreg_Ers con 11 ' $44 'def Erase Program Security Register ( 24bit address req) - write enable req prior
Flash_Bulk_Ers con 12 ' $C7 'def Bulk Erase command - write enable req prior
Flash_Globe_LCK con 13 ' $7E 'def Globel Block /Sector Lock : WEP must be 1 to setup and use - write enable req prior
Flash_Globe_UNLCK con 14 ' $98 'def Globle Block/Sector Unlock : WEP must be 1 to setup and use - write enable req prior
' commands 14-12 use the Read command ---
Flash_RD con 15 ' $03 'def read data at normal speed ( 24bit address req)+ (1 byte data)
Flash_Rd_HS con 16 ' $0B 'def read data at High speed (Fast Read) ( 24bit address req)+ (1dummy+1 byte data)
Flash_Rd_Secreg con 17 ' $48 'def Program Security Register read ( 24bit address req)+ (1 dummy +1 data)( simular to fast read command )
Flash_Rd_Sig con 18 ' $4B 'def read Flash device Unique ID signature - cmd + 4 dummy bytes , returns 64bit ID MSB first
Flash_Rd_Blk_LCK con 19 ' $3D 'def Read Block/Sector Lock status , returns 0= unlocked 1= Locked ( 24bit address req)+ (1 byte data)
Flash_Rd_ID con 20 ' $9F 'def Read manufacture 1byte/device/UID code 2 bytes ( JEDEC ID) - returns 3 bytes
Flash_Rd_reg2 con 21 ' $35 'def read the Status Register 2(S15-S8) - returns 1 data byte
Flash_Rd_reg3 con 22 ' $15 'def read the Status Register 3(S23-S16) - returns 1 data byte
'---- not in command lookup table - used directly -----
Flash_Wr_dis CON $04 'def write disable command
Flash_Rd_reg1 con $05 'def read the Status Register 1(S7-S0) - done by Bsy_chk routine
Flash_Wr_en con $06 'def write Enable command
Flash_Vol_Wr_EN con $50 'def Volatile SR Write Enable - used to change write_reg1 bits but wont set WEL flag - quick way of changeing register for protection bits ( no write enable
Flash_EN_Rst con $66 'def Enable Software Reset - reset takes min 30us
Flash_Rst Con $99 'def Do a Reset - Must be combined with Flash_EN_Rst
Flash_PWR_Dwn con $B9 'def Deep Power Down command
Flash_PWR_Up con $AB 'def Release From Deep Power Down command
' ---------- FLASH varables -------------------------
Data_Length var byte ' table of data length
SDC_buffer Var Byte[256] ' indexed data - max 256 bytes - 8mb FLASH has a 256 Limit from page Writes - Note 512 used in SD routines
SDC_data_in Var Byte ' Data in byte from flash
SDC_data_out Var Byte ' Data out byte from Flash -
SDC_address_High Var word ' address higher word sent to FLASH
SDC_address_Low Var word ' address lower word sent to FLASH
SDC_index Var Word ' Loop index counter
SDC_CmdCode Var Byte ' used here as Sector protect value for the Write Status register
SDC_cmd Var Byte ' command code for selected operation
SDC_Block var Byte ' 64K block Address - uses SDC_address_High.low , each block 0-63(32Kbit) 0-127(64Kbit), addressing used both
SDC_Sector var byte ' 4K Sector address - uses SDC_address_Low.highbyte , each sector = 16 pages , so sector 0 = page 0-15 - values = 0 -15
SDC_Page var byte ' Page Address
SDC_Byte Var byte ' Bytes Address
Flash_RD_Fast var bit ' Flag for High speed read 1 = Highspeed read speed 0= normal read speed
Flash_Install var bit ' flag set when flash install program used
Flash_32KB_Block_Sel var bit ' Sets StartPage address for 32KB Block erase - 0 = lower block - sets start page address - page 0 - 127, 1 = High block - page 128 - 256
Flash_Protect var bit ' Set Protect =1 / Unprotect =0 of a block , used as a read of block status as well
Flash_Blk_Orgin var byte ' Orgin sector value - copy sector command
Flash_Blk_Dest var byte ' destination sector value - copy Sector Command
Flash_Sec_Orgin var byte ' Orgin sector value - copy sector command
Flash_Sec_Dest var byte ' destination sector value - copy Sector Command
Flash_Page_Orgin var byte ' Orgin Page value
Flash_Page_Dest var Byte ' Dest Page Value
Flash_Page_Length var byte ' number of pages
Flash_Clear var bit ' flag to clear orginal sector 1= clear
Flash_Manf_id var byte ' manufacture id code
Flash_Manf_type var byte ' device type code
Flash_Manf_cap var byte ' device capacity code
Flash_tmp var byte ' used as a temp varable
Flash_tmp2 VAR BYTE ' used as a temp varable
Flash_Reg_val var byte ' Flash register value
Flash_Addr_Copy_Low var word ' low word temp storage of input address and data length
Flash_Addr_Copy_High var word ' high word temp storage of input address and data length
'----------- Varable settings at startup ---------------------------------------------
Flash_RD_Fast = 0 ' Set to normal read at start
Flash_Install = 0 ' set to 0 when flash install not being used
Flash_Clear = 0 ' set not to clear
Flash_32KB_Block_Sel = 0 ' set to use low address
'---------------- Routines ------------------
goto JumpOverSPIFLASH ' Jump to end of this include file for Correct compile
Flash_Init:
' do a read register command to clear the Flash register after power up
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_Rd_reg1 ' Send the read status register command byte
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
gosub buffer_clear ' clear varables area
return
' -----------------------------
Buffer_Clear:
For SDC_index = 0 To 255
SDC_buffer[SDC_index] = 0
next SDC_index
return
'---------------------------------------
Flash_Reset:
' routine to software reset the flash
' enable reset and reset must be consecutive
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_EN_Rst ' Send Enable Reset command
gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
SDC_data_out = Flash_Rst ' Send Reset command
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'-----------------------------------------
Flash_Format:
'Note wont work if any sectors are protected
' can take upto 50sec on 32mbit chip
sdc_cmd = Flash_Bulk_ers ' excutes as it sounds
gosub Flash_Comand
return
'-------------------------------------------------
Flash_Sec_Erase:
' assumes Block address 0-63
' assumes Sector value 0 -15
' erases 1 Sector at a time address (4KB)= 15 pages
' Erases wont work on sectors that are write protected
' sector erase take 400ms per instruction
SDC_pAGE = 0 ' ensure 0
SDC_pAGE = sdc_SECTOR << 4 ' shift given sector 0-15 to upper page value
sdc_cmd = Flash_Sec_Ers ' Erases sector ( 256 pages x 256 bytes )
SDC_address_high.byte0 = SDC_Block ' set sector Address 0 to 15 for chip
SDC_address_low.byte1 = SDC_Page ' set page start address 0 to 255
SDC_address_low.byte0 = 0 ' set byte start address 0 to 255
gosub Flash_Comand ' Do the command
return
'----------------------------------------------------
Flash_Blk32_Erase:
' assumes Block address
' assumes flag 32KB_Block_Sel 0 = bottom 32Kb start address page, 1= 128page address
' erases 1/2 a 64KB Block at a time address (32KB)= 128 pages
' Erases wont work on sectors that are write protected
' sector erase take min 120ms max 1.6Sec per instruction
IF Flash_32KB_Block_Sel = 0 THEN ' select offset page for 32 byte sector
SDC_PAGE = 0
ELSE
SDC_PAGE = 128
ENDIF
sdc_cmd = Flash_blk32_Ers ' Erases 32kB block ( 128 pages of 256 bytes )
SDC_address_high.byte0 = SDC_Block ' set block Address for chip
SDC_address_low.byte1 = SDC_PAGE ' set page start address 0 to 255
SDC_address_low.byte0 = 0 ' set byte start address 0 to 255
gosub Flash_Comand ' Do the command
return
'-------------------------------------------------------------
Flash_Blk64_Erase:
' assumes Block address
' erases a 64KB Block at a time address (64KB)= 256 pages
' Erases wont work on sectors that are write protected
' sector erase take min 160ms max 2.0Sec per instruction
sdc_cmd = Flash_blk64_Ers ' Erases 64kB block ( 256 pages of 256 bytes )
SDC_address_high.byte0 = SDC_Block ' set Block Address for chip
SDC_address_low.byte1 = 0 ' set page start address 0 to 255
SDC_address_low.byte0 = 0 ' set byte start address 0 to 255
gosub Flash_Comand ' Do the command
return
'------------------------------------------------------------------
Flash_Block_Copy:
' copys data from 1 block to another
' erases destination block - optional clean of orginal block
' assumes Flash_Sect_Orgin,Flash_Sect_Dest ,Flash_clear
' Erases wont work on blocks that are write protected
' block erase take 400ms per instruction
SDC_Block = Flash_Blk_Dest ' clear destination block
gosub Flash_blk64_Erase ' use SDC_blk64_erase info to erase destination sector
for SDC_PAGE = 0 to 255 ' copy pages to selected block ( 256bytes at a time)
SDC_Block = Flash_blk_Orgin ' block to copy
SDC_byte = 0
Data_Length = 255
gosub Flash_Read ' read the data to buffer
SDC_Block = Flash_Blk_Dest ' block to copy to
SDC_byte = 0 ' use block details for destination
Data_Length = 255
gosub Flash_Write ' write the data
next SDC_PAGE
if Flash_clear = 1 then
SDC_Block = Flash_Blk_Orgin ' clean up orgin Block
gosub Flash_Blk64_Erase
endif
return
Flash_Page_Copy:
' copys data from pages 0 -255 from orgin or destination block
' assumes destination block pages are Erased
' assumes pages orgin and pages destination do not cross block boundrys
' assumes Flash_Page_Orgin,Flash_Page_dest ,Flash_Page_length, Flash_blk_orgin ,Flash_blk_dest
' writes wont work on blocks that are write protected
for Flash_tmp2 = Flash_Page_Orgin to Flash_Page_length ' copy sector 0 pages to selected sector 0 ( 256bytes at a time)
SDC_Block = Flash_blk_Orgin ' sector to copy
SDC_PAGE = Flash_tmp2
SDC_byte = 0
Data_Length = 255
gosub Flash_Read ' read the data to buffer
SDC_Block = Flash_blk_Dest ' sector to copy to
SDC_PAGE = Flash_Page_Dest ' page to copy to
SDC_byte = 0
Data_Length = 255
gosub Flash_Write ' write the data
Flash_Page_Dest = Flash_Page_Dest + 1 ' increment destination page
next Flash_tmp2
return
'----------------------------------------
Flash_Write:
' assumes data length , address and upto 256 bytes in SDC_buffer[] to send
' writes bytes from SDC_buffer[] into flash , block/page/byte loction must be "FF" at start
' write wont work on sectors that are write protected
sdc_cmd = Flash_WR ' excutes as it sounds - max of 256 bytes
SDC_address_high.byte0 = SDC_Block ' set block Address for chip
SDC_address_low.byte1 = SDC_Page ' set page start address 0 to 255
SDC_address_low.byte0 = SDC_byte ' set byte start address 0 to 255
gosub Flash_Comand
return
'--------------------------------------
Flash_Read:
' assumes Block, page, bytes , data length input
' gets upto bytes data into SDC_buffer[] from flash
' uses normal read speed if no Flash_RD_Fast flag set
if Flash_RD_Fast = 1 then
sdc_cmd = Flash_Rd_HS ' excutes fast read - max of 256 bytes
else
sdc_cmd = Flash_RD ' excutes normal read - max of 256 bytes cos of buffers size/ page size
endif
SDC_address_high.byte0 = SDC_Block ' set block Address for chip
SDC_address_low.byte1 = SDC_Page ' set page start address 0 to 255
SDC_address_low.byte0 = SDC_byte ' set byte start address 0 to 255
gosub Flash_Comand
return
Flash_WR_protect:
' routine to protect/ unprotect a set block of 60-63 in 32kbit chip ( block 60-63 used by K9 system stored settings )
' Assumes Flash_Protect - 0 = unprotect 1 = Protect a sector
' SETUP FOR 32kB CHIP
' Bit7 = SRP0 - Set to 0 - software protect (SRP1= 0 DEPHALT(stat_reg2(bit0), not WP pin
' bits6(SEC) = 0 = 64KB Block 1= 4Kb SECTOR , Bit5(TB) 0= Top, 1 = Bottom , Bit4-2 = BP2-BP0. bits 1-0 (wel, busy )
if Flash_Protect = 0 then
SDC_buffer[0] = $00 ' clear all blocks
else
SDC_buffer[0] = $0C ' set blocks 60-63 protected for K9 project
endif
sdc_cmd = Flash_Wr_reg1 ' write register
data_length = 1 ' set 1 byte
gosub Flash_Comand
return
'-----------------------------------------------------------
Flash_WR_Disable:
' reset the write enable latch
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_Rd_reg1 ' Send the read status register command byte
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'----------------------------------------------------
Flash_Read_ID:
' returns JEDEC ID- returns Manufacture ID byte($EF), mem type - (ID15-ID8)1byte ,capacity(ID7-ID0)1byte)
sdc_cmd = Flash_Rd_ID ' Flash Read ID
data_length = 3 ' 3 bytes
gosub Flash_Comand
Flash_Manf_id = SDC_buffer[0]
Flash_Manf_type = SDC_buffer[1]
Flash_Manf_cap = SDC_buffer[2]
IF FLASH_Install = 1 then
HSEROUT ["Flash Manf ID = ",hex Flash_Manf_id," Flash Device ID = ",hex Flash_Manf_type," Device Capacity ID = ",hex Flash_Manf_cap,13,10]
endif
return
'---------------------------------------------------------------------
Flash_Read_Sig:
' returns the flash chips Unique ID number ( 64Bit)
sdc_cmd = Flash_Rd_Sig ' Flash Read Unique ID signature
data_length = 4 ' 4 bytes ' Flash Read Unique ID signature
gosub Flash_Comand
return
'----------------------------------------------
Flash_Read_BLK_Lock:
'routine to read block or sector locks ( WPS=1 to work )
sdc_cmd = Flash_Rd_Blk_LCK ' Flash Read block lock
data_length = 1 ' 1 bytes
gosub Flash_Comand
Flash_Protect = SDC_buffer[0] & $01 ' get bit0 value - 1 = locked .0 = unlocked
return
'---------------------------------------------
Flash_Power_Down:
' sEt Flash chip to low power mode from standby mode - no command other tha powerup will wake the device
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_PWR_Dwn ' command to pwr down
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'----------------------------
Flash_Power_Up:
' sEt Flash chip to standby mode - no command other tha powerup will wake the device
' sEt Flash chip to low power mode from standby mode - no command other tha powerup will wake the device
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_PWR_Up ' command to pwr up
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'-----------------------------
' -----------------------------
Flash_Read_reg2:
' reads write register 2 -
' Register 2 controls .....
' bit7(S15)- Suspend Status
' bit6(S14)CMP -Compliment Protect - dephalt CMP =0
' bit5-3(S13-11)- Security Register(One time programable) dephalt = 000
' bit1(S9) - QE - Quad SPI Mode Enable ( default =0 when chips NOT FVIQ type)
' bit0(S8) - SRP1- Protect bit1 _ dephalt =0
'
sdc_cmd = Flash_Rd_reg2 ' Flash Read register 2
data_length = 1 ' 1 bytes returned
gosub Flash_Comand
return
'---------------------------------------
Flash_Read_reg3:
' Register 3 controls .....
' bit7(S23) - Hold(0- dephalt)/Reset(1) pin fuction
' bit6,5(S22,S21)(0,0=100%),(0,1=75%),(1,0=50%),(1,1 =25%- dephalt) read driver strength- used to overcome cpacitive loading ,trace impendace issues with signal at high speed reads
' bits4,3 - reserved (writen as 0)
' Bit2(S18) WPS - selects Protection methode - Indervidual block/sectors(WPS=1) or by grouping range(WPS=0) ( WPS dephalt is 0 )
' Bits1,0-reserved(writen as 0)
sdc_cmd = Flash_Rd_reg3 ' Flash Read register 3
data_length = 1 ' 1 bytes returned
gosub Flash_Comand
return
'-----------------------------------
Flash_Comand:
' assumes SDC_address long
' assumbe data_Length = Lookup table to fill
' max 256 bytes per write
' erase of the sector by byte / bulk is needed prior to write , as a write only changes a 1 to 0 , and the erase chanse the 0 to 1
if SDC_cmd = 0 then return ' invalid command if value =0
Lookup SDC_cmd,[$00,$01,$31,$11,$02,$42,$20,$52,$D8,$36,$39,$44,$C 7,$7E,$98,$03,$0B,$48,$4B,$3D,$9F,$35,$15],SDC_CmdCode ' asignes command code to flash chip
Flash_tmp = 0 ' ensure 0 - counter for busychk loop
gosub BSY_chk ' do for all commands
if SDC_cmd <=14 then ' do for writes, sector erase,bulk erase , write reg protect - commands 1-14 use writen enable first
FLASH_CE = 0 ' Bring the FLASH chip select line low.
SDC_data_out = Flash_Wr_en ' Send command byte that requires a write
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
FLASH_CE = 1 ' Bring the FLASH chip select line high to complete the write command
pauseus 1 ' pause between prev command - may not need
endif
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = SDC_CmdCode ' Send the command byte,
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
if SDC_cmd =>4 and SDC_cmd <=11 or _ ' if write commands 4-11 then use 24bit address assigned
SDC_cmd =>15 and SDC_cmd <=19 then ' or read commands 15-19 then use 24bit address assigned , command 18 uses 24bit address as 3 dummy bytes
SDC_data_out = SDC_address_high.Byte0 ' set block Address for chip
Gosub Flash_spiw ' Write Byte SDC_data_out.
SDC_data_out = SDC_address_low.Byte1 ' set page address 0 to 255
Gosub Flash_spiw ' Write Byte SDC_data_out.
SDC_data_out = SDC_address_low.Byte0 ' set byte address 0 to 255
Gosub Flash_spiw ' Write Byte SDC_data_out.
if SDC_cmd => 16 and SDC_cmd <= 18 then ' if read High speed mode ,Program security read , Read Unique ID(add 4th dummy byte)
SDC_data_out = $00 ' add a dummy byte to command
Gosub Flash_spiw ' Write Byte SDC_data_out.
endif
endif
if SDC_cmd <=5 or _ ' if write commands require data bytes sent
SDC_cmd >=15 and SDC_cmd <= 22 then ' or read commands require data bytes returned
For SDC_index = 0 To Data_Length-1 ' DATA LENGTH -1 so byte 0 is counted when setting data length
if SDC_cmd <= 5 then ' if write ,Write register,write Security register then
SDC_data_out = SDC_buffer[SDC_index] ' send contents of indexed SDC_buffer
gosub Flash_SPIw ' write byte SDC_data_in from SPI bus. Returns SDC_data_in.
endif
if SDC_cmd =>15 and SDC_cmd <=22 then ' if read scommand returns data
gosub Flash_SPIR ' Read Byte SDC_data_in from SPI bus. Returns SDC_data_in.
SDC_buffer[SDC_index] = SDC_data_in
endif
Next SDC_index
endif
pauseus 1
FLASH_CE = 1 ' Bring the FLASH chip select line high.
return
'----------------------------------------------------
Bsy_chk:
FLASH_CE = 0 ' Bring the FLASH chip select line low
SDC_data_out = Flash_Rd_reg1 ' Send the read status register1 command byte
Gosub Flash_spiw ' Write Byte SDC_data_out. , subroutine writes a byte on the SPI bus
Flash_tmp = 0 ' clear counter
while Flash_tmp <150 ' loop test read for busy ( counter may need to be increased depending on size of chip and time for block erase command to complete
gosub Flash_SPIR ' Read Byte SDC_data_in from SPI bus. Returns SDC_data_in.
IF FLASH_Install = 1 then
Flash_Reg_val = SDC_data_in ' get value of read status reg value for use in flash install program checks for protection
HSEROUT ["STATUS REG = ",hex Flash_Reg_val,13,10] ' show on terminal when doing flash install
HSEROUT ["Flash_tmp = ",dec2 Flash_tmp,13,10]
endif
Flash_tmp = Flash_tmp + 1
SDC_data_in = SDC_data_in & $01 ' mask bit 0 ( busy flag)
if SDC_data_in = 0 then Flash_tmp = 151 ' Test bit 0 if write not busy,force exit of loop
wend
FLASH_CE = 1 ' Bring the FLASH chip select line high
return
'-------------------------------
Flash_SPIR:
SO = 1 ' Shift out high bits while shifing in data.
Shiftin SO, SCK, 6,[SDC_data_in] ' MSb first, clock idle high.
Return
'-------------------------------
Flash_SPIW:
shiftout SI,SCK,5,[SDC_data_out] ' MSb first, clock idle high.
return
'------------------------
JumpOverSPIFLASH: