PDA

View Full Version : How to post Code



Terry
- 6th January 2012, 17:45
Quick question, how do I post code within the window on the forum, I have looked on the the site, but I can't find it, I am sure it is very simple to do.

Thanks,
Terry

Darrel Taylor
- 6th January 2012, 19:11
At the bottom of each thread, there is a "Posting Permissions" box.
In there you'll see a "BB code (http://www.picbasic.co.uk/forum/misc.php?do=bbcode)" link.

That page shows all the different things you can do in a post on the forum.
The one you want is "Code".

HTH,

mackrackit
- 6th January 2012, 21:39
Once you click on the reply button you will want to click on the Go Advanced button.
Then you should see a tool bar above the editor box. The "#" will give you the code tags.
You will also want to click the upper left button of the tool bar to go into source mode, it works better than WYSIWYG.

Demon
- 7th January 2012, 21:56
Good place to see if my code posts properly. I've seen some have problems with %.


'************************************************* ***************
'* Name : LAB X1 16F877 Timer Interrupt.BAS *
'* Author : Demon *
'* Notice : Copyright (c) 2012 *
'* : All Rights Reserved *
'* Date : 2012-01-06 *
'* Version : 1.0 *
'* Notes : PIC Basic Pro v2.60C *
'* : MicroCode Studio Plus v2.2.1.1 *
'* : MPASM v3.50 *
'* : Lab X1 Experimental Board *
'* : MeLabs U2 Programmer v4.32 *
'************************************************* ***************
'define LOADER_USED 1

' Comment out CONFIG in MPASM include (File: 16F877.INC in PBP folder).
@ __config _HS_OSC & _WDT_OFF & _PWRTE_ON & _BODEN_ON & _LVP_OFF & _CPD_OFF & _WRT_ENABLE_OFF & _DEBUG_OFF & _PWRTE_OFF

define OSC 20

DEFINE LCD_DREG PORTD ' Set LCD data port
DEFINE LCD_DBIT 0 ' Set starting data bit
DEFINE LCD_RSREG PORTE ' Set LCD register select port
DEFINE LCD_RSBIT 0 ' Set LCD register select bit
DEFINE LCD_EREG PORTE ' Set LCD enable port
DEFINE LCD_EBIT 1 ' Set LCD enable bit
DEFINE LCD_BITS 8 ' Set LCD bus size
DEFINE LCD_LINES 2 ' Set number of lines on LCD
define LCD_COMMANDUS 2000 ' Set command delay time in microseconds
DEFINE LCD_DATAUS 50 ' Set data delay time in microseconds

TRISD = %00000000 ' Set all port D pins to output
TRISE = %00000000 ' Set all port E pins to output

ADCON1 = 7 ' A/D off, all digital

wsave VAR BYTE $70 SYSTEM ' Required by Instant Interrupt routine

PAUSE 1000 ' Wait for LCD to initalize
LCDOUT $FE,1,"LabX1 16F877 Tim Int"

'---[INT - interrupt includes]--------------------------------------------------
INCLUDE "DT_INTS-14.bas" ; Base Interrupt System
INCLUDE "ReEnterPBP.bas" ; Include if using PBP interrupts
INCLUDE "Elapsed_INT.bas" ; Elapsed Time interrupts

'---[INT - interrupt definition]------------------------------------------------
ASM
INT_LIST macro ; IntSource, Label, Type, ResetFlag?
INT_Handler TMR1_INT, _ClockCount, PBP, yes
endm
INT_CREATE ; Creates the interrupt processor
ENDASM

@ INT_ENABLE TMR1_INT ; Enable Timer 1 Interrupts

GOSUB ResetTime ' Reset Time to 0d-00:00:00.00
GOSUB StartTimer ' Start the Elapsed Timer

Main:
IF SecondsChanged = 1 THEN
SecondsChanged = 0
LCDOUT $FE,$C0, DEC Days,"d-",DEC2 Hours,":",DEC2 Minutes,":",DEC2 Seconds
ENDIF
GOTO Main

end

WOOT! It worked!

Robert
:)